INSTALLATION INSTRUCTIONS - RETROFIT BATTERY FLUSHOMETER (cont’d)
210381 Rev. A
Page 3
STEP 6: Operation Mode (cont’d)
Factory pre-set functions are:
MAKING ADJUSTMENTS TO THE ELECTRONIC FEATURES
(Optional: Only required if factory settings are not preferred)
Once in operation mode, if adjustments are preferred, installer must move into set up mode.
If desired adjustments are not made within 30 minutes of initial power-up, the power must be disconnected for 10 seconds and
then reconnected to obtain another adjustment period.
STEP 7: Set-Up Mode
If 30 minutes have passed since the initial power-up of the valve - open up the battery compartment (Figures 7 and 8) and disconnect the
battery snap for 10 seconds. Reconnect and replace the cover and screws. If hardwired - disconnect battery snap to the hardwire
converter for 10 seconds.
7RPRYHIURPRSHUDWLRQPRGHLQWRVHWXSPRGHSXVKDQGKROGHOHFWURQLF
override button for five seconds. Release the electronic override
button when a solid blue light is visible.
7KHZDWHUFORVHWIOXVKRPHWHUPRGHOVKDYHVHWWLQJVZKLFKDUHadjustable via the Set-Up Mode - Bowl Length Selection, Dual
Flush and 24 Hour Flush Adjustment.
:KLOHLQ6HW8S0RGHWKHXVHUZLOOPRYHWKURXJKWKHGLIIHUHQWDGMX
stment modes one by one, in the order as described above. Use the
electronic override button to toggle through the different settings of the adjustment feature being altered. To advance to the next adjust-
ment mode, hold down the electronic override button until blue light is present, then release the button. See Figure 5.
STEP 8: Making Adjustments
(Optional: Only required if factory settings are not preferred)
INSTALLATION INSTRUCTIONS - HARDWIRED FLUSHOMETER
STEP 1:
%HIRUHLQVWDOOLQJWKHIOXVKYDOYHERG\,QVWDOO´[´HOHFWULFDOER[LQ
to wall with centre of box in line with the cut-out in the back of the
metal flush valve cover. See Figure 3.
Securely attach box to wall structure. Install CSA and/or UL approved Class 2 transformer
(or equivalent) in a convenient adjacent location, or in a pipe chase.
(Do NOT install the
transformer inside the control box.)
Run suitable wires which comply to local electrical
codes for a 1 amp load (No. 18 cable is usually sufficient) from 24 VAC step down transformer
into the electrical box.
$VVHPEOHSODVWLFEXVKLQJLQWRWKHKROHRQWKHFRYHUSODWH
0HDVXUHDQGFXWWXEHDVVHPEO\WRDSSURSULDWHOHQJWKVRWKDWWKHEXV
hing will fit under the
metal flush valve cover and the free end will protrude into the box through the coverplate by
1/2” minimum. Rotate cover gasket, if necessary, so that the U-shaped wire guides align with
the rear opening in valve cover.
3HUIRUPVWHSVDQGRQSDJH:KHQUHDG\UHPRYHPHWDOFRYHUDQGIHHGWKHZLUHV
from the hardwire converter through the tube assembly and the tube assembly through the
bushing on the coverplate.
$WWDFKWKHFRQYHUWHUZLUHVWRWKH9$&ZLUHVIURPDVWHSGRZQWUDQVIRUPHU
:LWKSRZHUWRWKHIOXVKRPHWHU\RXZLOOVHHDQDVFHQGLQJDQGGHVFHQ
ding light sequence to
signify that the valve is now in operation mode.
$VVHPEOHFRYHUSODWHXVLQJWKHEUDFNHWDQGVFUHZVSURYLGHG
:LWKWKHWXEHEXVKLQJORFDWHGLQSRVLWLRQDVVHPEOHPHWDOFRYHUWRIO
ush valve body with tube assembly located in metal cover cut-out.
STEP 2:
2SHQLQOHWVWRS
NOTE:
Hardwire junction box installed behind
flush valve on the centreline of fixture.
Fig. 3
WC bowl length of 24”, 24 hour flush is off, Dual Flush feature is on.
w w w . s p e c s e l e c t . c o m
Bowl Length
Fig. 4
8.1 Sensor Adjustment:
For Waterclosets:
Configure the sensing ranges by selecting the appropriate bowl length. Refer to Figure 5 for the
different bowl length settings.
The bowl length is the distance from the centre line of the valve to the lip of the bowl (see Figure 4).
To ensure the correct distance is selected, stand or place a target at the end of the bowl. Starting
with one illuminated red light, step through the distances until the blue light begins to flash.
The flashing light confirms that the sensor is configured for that bowl length.
NOTE
the WC bowl length setting is
NOT
the sensing range. The advanced sensor activated flush
system uses multiple detection distances and the bowl length to react appropriately to different
usage patterns.
,IQRIXUWKHUOHQJWKDGMXVWPHQWVDUHGHVLUHGDGYDQFHWR'XDO)OXVK$GMXVWPHQWPRGH
To advance to Dual Flush Adjustment mode, press and hold down electronic override button for 5
seconds until the solid blue light is present.
Release electronic override button.
