background image

9

ASSEMBLY

ASSEMBLY TOOLS REQUIRED

ASSEMBLY TIME ESTIMATE

1.

Attach the column (A) Fig. 3 to the base (B) using the
four 1-3/4" bolts (C), three of which are shown.
Loosely thread the locking lever (D) into the table
mounting bracket (E). Loosely thread the remaining
locking lever (F) Fig. 4 into the split of the table
mounting bracket (E).

2.

Insert the table (G) Fig. 4 into the table mounting
bracket (E) Fig. 3 and tighten the lever (D) Fig. 4 to
lock the table in position. Tighten the locking lever
(F) Fig. 4 to lock table-raising mechanism on the
column.

3.

Attach the table adjusting handle (H) Fig. 4 to the
table mounting bracket (E).

4.

Carefully position the drill press head (J) Fig. 5 on the
column (A) as far as it will go. Align the drill press
head (J) Fig. 5 and the table (G) Fig. 4 with the base
of the drill press, and tighten the locking lever (K) and
set screw (L) with the supplied hex wrench (M).

5.

Thread the three pinion shaft handles (N) Fig. 6 into the three holes in the pinion shaft (P).

6.

IMPORTANT:

Make certain the spindle (R) Fig. 7, and chuck (S) are free of any grease, lacquer or rust preventive

coatings.

NOTE:

If necessary, household oven cleaner can effectively remove these coatings from the spindle and chuck. Carefully

follow the manufacturer’s safety rules regarding its use.

7.

Insert the chuck (S) Fig. 7 on the spindle (R) as far as it will go.

A

B

C

D

E

D

G

E

H

F

J

K

L

A

M

N

N

P

R

S

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

For your own safety, do not connect the machine to the power source until the machine is
completely assembled and you read and understand the entire instruction manual.

3mm Hex Wrench (Supplied)               5mm Hex Wrench (Supplied)               Adjustable Wrench

The assembly time for this unit is approximately 1-2 hours.

Содержание 17-965


















Отзывы: