Delta 11-900 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 16

Delta 11-900 Скачать руководство пользователя страница 8

8

Fig. 16

Fig. 17

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE
IS LONGEST OF THE 3 BLADES

GROUNDED OUTLET BOX

GROUNDING MEANS

ADAPTER

MOTOR SPECIFICATIONS

Your drill press is wired for 110-120 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the

“OFF”

position. The motor provides a no-load speed of 1725 RPM.

GROUNDING INSTRUCTIONS

WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC

SHOCK.

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance
with all local codes and ordinances.

Do not modify the plug provided if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment grounding conductor can result in risk of electric shock. The conductor with
insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a
live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or
if in doubt as to whether the tool is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding types plugs and 3-hole receptacles that accept the tool’s
plug, as shown in Fig. 16.

Repair or replace damaged or worn cord immediately.

This tool is intended for use on a normal 120-volt circuit
and has a grounded plug that looks like the plug
illustrated in Fig. 16.

If a properly grounded outlet is not available, a temporary
adapter, shown in Fig. 17, may be used for connecting
the 3-prong grounding type plug to a 2-prong receptacle.
The temporary adapter should be used only until a
properly grounded outlet can be installed by a qualified
electrician. The green colored rigid ear, lug, or the like
extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet
box cover. Whenever the adapter is used, it must be held
in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is
not permitted by the Canadian Electric Code

.

CAUTION: IN ALL CASES, MAKE CERTAIN THE RE-
CEPTACLE IN QUESTION IS PROPERLY GROUNDED.
IF YOU ARE NOT SURE HAVE A CERTIFIED ELEC-
TRICIAN CHECK THE RECEPTACLE.

«
...
6
7
8
9
10
...
»

Содержание 11-900

















Отзывы:

Нет отзывов