Delta Electronics DEP-008 A Скачать руководство пользователя страница 1

Evaluation Procedure 
(DEP-008 A) 

 

The Delphi DNS Series of SIP type 
POL converters 

 
The DNS, 2.4~5.5V or 10~14V input,
programmable output,

 

non-isolated point of load

DC/DC converters, are the latest offering from
one of the world’s largest power supply
manufacturers 

 Delta Electronics, Inc. The

DNS converters have flexible and programmable
tracking and sequencing features to enable a
variety of startup voltages as well as sequencing
and tracking between power modules. With
creative design technology and optimization of
component placement, these converters possess
outstanding electrical and thermal performance,
as well as extremely high reliability under highly
stressful operating conditions. All models
possess a myriad of standard protection
features. 
 
This document guides the user through the
evaluation procedures to qualify a POL module.
The data shown in this Evaluation Procedure is
for the SIP Package Type POL evaluation board.
Please refer to the appropriate technical data
sheet for detailed performance and technical
information for the specific POL units.

 

Evaluation Procedure 
EP_DNS_SIP_08052004

 

DNS SIP Series 

                                                             

 

 
 

 

1.0   Purpose 

 

This document guides the user in performing 
electronic measurements on a DNS POL (point 
of load) DC/DC converter using the Delta 
Evaluation Board. 

 

2.0 Relevant Documentation 

 

The documentation and background information 
listed below is relevant to this evaluation 
procedure: 
 

2.1 Appropriate date sheet for the DNS Series 

unit under evaluation. 

2.2 Power Module Evaluation Board Schematic.
2.3 Power Module Evaluation Board Layout.  
2.4 General Test and Safety Procedures. 

 

 
 
 
 

Delta Electronics, Inc.

1

Содержание DEP-008 A





















Отзывы: