background image

 

 

 

Document Title: 

BI-NEU RTM Homologation Description 

Page 4 / 5

 

 

 

Equipment Type 

RF Receiver 

Country of Origin: 

Mexico 

Operating Voltage 

7.0VDC to 24VDC  
8.0 VDC to 16VDC 
(Nominal) 

Operating Temperature 

-40 deg C to + 105deg C 

Operating Freq Range 

902.425 MHz +/- 210kHz 
(RKE Channel 1) 
902.375 MHz +/- 210kHz 
(RKE Channel 2) 
903./- 360kHz 
(PEPS Channel) 

315.000 MHz +/- 360 kHz 

(TPM) 

Modulation 

FSK w/ + 7.5kHz 
Deviation (RKE) 
FSK w/ + 15kHz (PEPS) 
ASK (TPM) 
FSK w/ +35kHz deviation 
(TPM) 

RX Data Frame Size 

105 bits (RKE) 
80 bits (TPM) 
85 bits to 160 bits (PEPS) 

RX Data Rate 

2.1kbps +/- 0.4% (RKE) 

9.6 kbps +/- 0.4% (TPM) 

9.6 kbps +/- 0.4% (PEPS) 

RX Data Encoding 

Manchester 

Antenna Type: 

Integral Diversity antenna 
structure for RKE and 
single antenna for TPM 
reception 
(Insert dimensions from 
part dwg) 

TX Operating Freq Range  902.425 MHz +/- 40kHz 

(RKE Channel 1) 

902.375 MHz +/- 40kHz 

(RKE Channel 2) 

Antenna Gain 

N/A 

TX Data Frame Size 

37 bits 

TX Modulation 

OOK 

TX Data Encoding 

Manchester 

TX Data Rate 

1.95kHz +/- 0.4% 

 
 
 

2.3.1  Modes of Operation 

The EUT is powered via a fused feed from the vehicle battery power distribution center and the feed is always 
active.   

2.3.1.1 Receive 

The EUT has two modes of Receiver operation depending upon the vehicle status: 

 

Receiver is periodically activated and deactivated (Polling mode) whenever the RTM is not awake and 
the vehicle CAN serial bus is asleep.  

o

 

 

Note: Polling operation requires RKE Fob ID’s to be learned and/or TPM functionality to be 

enabled. 

 

Receiver is continuously active whenever RTM is awake or vehicle CAN serial bus is awake. 

2.3.1.2 Transmit 

The EUT transmit operation is activated whenever a valid received RF data message contains a Vehicle status 
request action code.  TX mode is terminated when the message has been transmitted.  RX mode will not be 
active when the EUT TX mode is in operation. 

 

Vehicle status request transmission from RKE Fob occurs either following a vehicle Remote Start or 
Stop request or after a certain period of time expires following the receipt of a function pending status 
request. 

Содержание DG9T-15K619-CF






Отзывы: