20
14.1 Installing the filter
42
1. Remove the filter (C4)
from the packaging.
2. Turn the date indicator
disk (see fig. 42) until the
next two months of use
are displayed.
Please note
The filter lasts about two
months if the appliance is used
normally. If the coffee machine
is left unused with the filter in-
stalled, it will last a maximum of three weeks.
3. To activate the filter, run tap water through the hole in the
filter as shown in the figure until water comes out of the
openings at the side for more than a minute (fig. 43).
44
43
17 fl. oz
0,5 l
4. Extract the tank (A16) from the appliance and fill with
water.
5. Insert the filter in the water tank and immerse it complete-
ly for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (fig. 44).
6. Insert the filter in the filter housing (A17 - fig. 45A) and
press as far as it will go.
7. Close the tank with the lid (A18 - fig. 45B), then replace the
tank in the machine.
45A
45B
When you install the filter, you must notify the appliance of its
presence.
8. Press the
MENU/ESC
button (B2) to enter the menu;
9. Press (B9) or (B10) (fig. 6) until “Install filter” appears
on the display (B4);
10. Press the
OK
button (B3) (fig. 7);
11. “Enable?” is displayed;
12. Press the
OK
button to confirm the selection. “HOT WATER
Press OK” is displayed;
13. Position a container under the hot water spout (C6) (min.
capacity: 17 fl.oz/500 ml);
14. Press the
OK
button to confirm the selection. The appliance
begins hot water delivery and the message “Please wait” is
displayed;
15. After the flow of hot water stops, the appliance automatically
resets to “Ready for coffee” status.
The filter is now active and you can use the coffee machine.
14.2 Replacing the filter
When “REPLACE FILTER” appears on the display (B4), after two
months (see date indicator) or when the appliance has not been
used for 3 weeks, you should replace the filter:
1. Extract the tank (A16) and exhausted filter (C4);
2. Take the new filter out of its packet and proceed as illus-
trated in points 2, 3, 4, 5, 6 and 7 in the previous section;
3. Position a container under the hot water spout (C6) (min.
capacity: 17 fl.oz/500 ml);
4. Press the
MENU/ESC
button (B2) to enter the menu;
5. Press (B9) or (B10) (fig. 6) until “Replace filter” ap-
pears on the display;
6. Press the
OK
button (B3 - fig. 7);
7. The message “Confirm?” is now displayed;
8. Press the
OK
button to confirm the selection;
9. “HOT WATER Press OK” is displayed;
10. Press the
OK
button to confirm the selection. The appliance
begins hot water delivery and the message “Please wait” is
displayed;
11. After the flow of hot water stops, the appliance automatically
resets to “Ready for coffee” status.
The new filter is now active and you can use the coffee machine.
14.3 Removing the filter
If you want to use the appliance without the filter (C4), you
must remove it and notify the appliance of its removal. Proceed
as follows:
1. Remove the tank (A16), remove the filter and put the tank
back in the appliance;
2. Press the
MENU/ESC
button (B2) to enter the menu;
3. Press (B9) or (B10) (fig. 6) until “Install filter, Enabled”
appears on the display (B4);
4. Press the
OK
button (B3 - fig. 7);
5. “Disable?” is displayed;
