DeLonghi PrimaDonna Elite ECAM 650.75.MS, Инструкция по эксплуатации

Страница: 11 / 31

11
”
• The message “TURNING OFF UNDERWAY PLEASE WAIT”
appears on the display, then (if envisaged) the appliance
performs a rinse cycle and goes of (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
•
irst turn the appliance of by pressing the button
(ig. 9);
• release the main switch (A21) at the back of the appliance
(ig. 2).
Important!
Never press the main switch while the appliance is on.
8. MENU SETTINGS
8.1 Rinsing
Use this function to deliver hot water from the cofee spouts
(A8) and hot water/steam spout (C6), if inserted, to clean and
heat the appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
cofee and hot water spouts (ig. 8).
To enable the function, proceed as follows:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ RINSING” appears on the
display (B);
3. Press “ ” to start rinsing.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. After a few seconds, hot water is delivered irst from the cof-
fee spouts, then from the hot water/steam spout (if insert-
ed) to clean and heat the appliance’s internal circuit. “RINS-
ING UNDERWAY, HOT WATER FROM SPOUTS” appears on the
display, together with a progress bar which ills gradually as
preparation proceeds;
5. To stop rinsing, press “ STOP” or wait for rinsing to stop
automatically.
Please note!
• If the appliance is not used for more than 3-4 days, when
you turn it on again, we strongly recommend performing
2/3 rinses before use;
• After cleaning, it is normal for the grounds container (A10)
to contain water.
8.2 Descaling
For instructions on descaling, see section “17. Descaling”.
8.3 Water ilter
For instructions on how to install the ilter (C4), see section “19.
Water softener ilter”.
8.4 Drinks settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each drink.
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ DRINKS SETTINGS” ap-
pears on the display (B);
3. Press “ ”. The values for the irst drink appear on the
display;
4. The reference user proile is highlighted on the display. The
values are displayed on vertical bars. The default value is
indicated by the , symbol, while the current value is
highlighted by the solid part of the vertical bar.
5. To go back to the settings menu, press “ ESC”.
To scroll and display the drinks, press NEXT;
6. To reset the default values for the drink displayed, press “
RESET”;
7. “CONFIRM RESET?”: to conirm, press “ OK” (to cancel,
press “ ESC”);
8. “RESET DEFAULT VALUES DONE”: press “ OK” .
The drink has been reset to the default values. Continue with the
other drinks, or go back to the settings menu.
8.5 Setting the time
To set the time on the display (B), proceed as follows:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ SET TIME” appears on the
display (B);
3. Press “ ”. The time setting panel appears on the display;
4. Press < o > corresponding to the hours and minutes until
the current time is displayed;
5. To conirm, press “ OK” (to cancel, press “ ESC”),
then press “ ESC” to go back to the homepage.
The time is now set.
8.6 Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make cofee immediately.
Please note!
To enable this function, the time must already be set correctly
(see section “8.5 Setting the time
”).
To enable auto-start, proceed as follows:
1. Press “
” (B2) to enter the menu;