DeLonghi La Specialista EC9335M, Руководство пользователя

Страница: 34 / 45

33
6. Replace the connection nozzle, move the ring downwards
and put the cappuccino maker back on the nozzle, turning
it and pushing it upwards until it is attached.
For more thorough cleaning, use De’Longhi detergent.
11. ACTIVATING THE WATER SOFTENER FILTER
Certain models are fitted with a water softener filter (C6). If this
is not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
To use the filter correctly, follow the instructions below.
1. Remove the filter from the packaging;
2. Turn the date indicator disk (fig. 30) until the next 2 months
of use are displayed;
Please note: The filter lasts about two months if the appliance is used normal-
ly. If the coffee machine is left unused with the filter installed, it will last a maximum
of 3 weeks.
3. To activate the filter, run tap water through the hole in the
filter (fig. 31) until water comes out of the openings at the
side for more than a minute;
4. Extract the tank (A17) (if necessary fill with water);
5. Insert the filter in the water tank and immerse it complete-
ly for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (fig. 32);
6. Place the filter in the filter housing (A18) and press as far
as it will go. Close the tank, then put the tank back in the
machine;
The filter is now active and you can use the coffee machine.
12. MENU SETTINGS
Please note: Once in the menu, you can modify all the menu functions as de-
scribed in the previous sections.
12.1 Coffee temperature
To change the temperature of the water used to make the coffee,
proceed as follows:
1. Press and hold the
(B3) and (B7) buttons togeth-
er for at least 3 seconds to access the menu. The (B15)
and (B16) lights alternate;
2. Turn the mode selection dial (B8) to the ESPRESSO
position. The light (B11) remains on steadily;
3. Press the button corresponding to the desired selection as
shown in the following table:
Button Temperature
Standard
High
4. Press the button (B1) to exit the menu. (If the appliance
is left idle for about 1 minute, it exits automatically from
the settings menu and is ready for use again).
12.2 Water hardness
The descale light (B9) comes on after a period of time es-
tablished according to water hardness. The machine can also
be programmed according to the actual hardness of the water
supply in the various regions, in which case descaling may be
required less frequently.
Proceed as follows:
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C4)
from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
4. Press and hold the (B3) and (B7) buttons for at
least 3 seconds to access the menu. The (B15) and
(B16) lights alternate;
5. Turn the mode selection dial (B8) to the AMERICANO
position. The light (B9) remains on steadily;
6. Press the button corresponding to the desired selection as
shown in the following table:
Total Hardness Test result Button Level
1
soft water
2
medium
water
3
hard or
very hard
water
7. Press the button (B1) to exit the menu. (If the appliance
is left idle for about 1 minute, it exits automatically from
the settings menu and is ready for use again).
12.3 Auto-off
Auto-off can be set so that the appliance goes off after 9 min-
utes, one and a half hours, or three hours. Proceed as follows:
1. Press and hold the
(B3) and (B7) buttons for at
least 3 seconds to access the menu. The (B15) and
(B16) lights alternate;
2. Turn the mode selector dial (B8) to the COFFEE posi-
tion: The light (B13) remains on steadily;
3. Press the button corresponding to the desired selection as
shown in the following table: