DeLonghi ECAM51X.55 series, Инструкция по эксплуатации

Страница: 13 / 29

12
6. “Confirm?”: Press to confirm or to go back
to the previous screen;
7. “Empty grounds container”: extract and empty the
grounds container (A20). Press ;
8. “Empty drip tray”: empty the drip tray (A24) and put back
in the appliance complete with grounds container and
grille (A23). Press ;
9. “Place 0.5l container under spouts”: position a container
under the coffee spouts (A14) and hot water spout (C6).
Press ;
Important! Danger of burns
Do not leave the appliance unattended while the circuit is
emptying.
10. “Rinsing, Please wait”: the appliance performs a rinse cycle
from the coffee spouts;
11. “Empty water tank”: remove the tank (A18), empty it com-
pletely, then press ;
12. (If the filter is installed) “Remove filter”: remove the filter
from the tank, then press ;
13. “Insert tank, Press OK”: put the tank back in then press
;
14. “Water circ. emptying underway”: wait for the appliance to
empty the circuit; (Important: hot water from the spouts!);
As the circuit empties, the appliance may make more
noise: this is completely normal.
15. “Empty drip tray”: remove, empty and reposition the drip
tray, then press ;
16. “Emptying complete press ok to turn off”: press .
The appliance goes off.
Please note!
The next time you turn the appliance on, the circuit will need to
be filled: follow the instructions in point 3 of section “5.1 Set-
ting up the appliance”.
16.1 Program beverages
The appliance is set by default to automatically deliver standard
quantities. To modify this quantity and customise the directly
selected beverages and the “DRINK MENU” (B4), pro-
ceed as follows:
1. Prepare the appliance for preparation of the beverage as
described in section “4.2 Making automatic recipes using
coffee beans” or sections “5.3 Filling and attaching the milk
container” and “8.1 Adjusting the amount of froth”;
2. Press (B2) to enter the “Settings” menu;
3. Press the selection arrows (B4) or (B5) until
“Prg. beverages” is displayed between the two dotted
lines;
4. Press (B3) to confirm: the appliance will list the
beverages that can be customised;
5. Press the selection arrows or until the de-
sired beverage is displayed between the two dotted lines:
press
to confirm;
6. Beverages with coffee: the display shows “Program
aroma”: press the selection arrows or until
selecting the desired aroma (see section “4.1 Temporarily
varying the coffee aroma”), press to confirm the
selection. Beverage preparation then commences and
the display shows “Program coffee” with a progress bar
that indicates the quantity delivered: once the desired
quantity has been delivered, press or .
Cappuccino and milk-based coffees: after having se-
lected and confirmed the aroma, beverage preparation
commences and the display shows “Program milk” with a
progress bar that indicates the quantity of milk delivered:
once the desired quantity has been delivered, press
or . The appliance then prepares the coffee: press
or to stop delivery when the desired quan-
tity of coffee has been delivered.
Hot water:
press . Delivery commences: once
the desired quantity has been delivered, press or
.
7. “Save parameters?”: to save the settings, press or
(otherwise press or ).
8. “Parameters saved” (or “Parameters not saved”). The appli-
ance is ready for use again.
Press or to terminate the preparation at any time.
Please note!
The display shows “
OK
“ - (B5) when the length
reaches the minimum programmable quantity.
8.1 Program My beverages
Follow the procedures described in the previous section “16.1
Program beverages” customise the beverages in the
(B5)
by selecting “Prg. My beverages” from the settings menu, or
proceed with direct programming, as described in section “11. “
“ Programming and selecting”.
8.2 General
Here you can find the settings to customise the basic functions
of the appliance:
1. Press (B2) to enter the “Settings” menu;
2. Press the selection arrows (B4) or (B5) until
“General” is displayed between the two dotted lines: press
(B3) to confirm;
3. Press the selection arrows (B4) or (B5) until
the required item is displayed between the two dotted
lines, then follow the specific instructions for each setting: