DeLonghi ECAM21.11X, Инструкция по эксплуатации

Страница: 10 / 20

9
Light flashing: the appliance must be descaled
(see the section “Descaling”).
Light on steadily: the appliance is performing a
descaling cycle.
ECO
ECO “Energy Saving” mode is active.
BEFORE USE
Checking the appliance
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De’Longhi
Customer Services.
Installing the appliance
Important!
When you install the appliance, you should respect the fol-
lowing safety warnings:
• The appliance gives off heat. After positioning the applian-
ce on the worktop, leave a space of at least 3 cm between
the surfaces of the appliance and the side and rear walls
and at least 15 cm above the coffee machine.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces (e.g.
electric hot plates).
Setting up the appliance
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
Using the appliance for the first time
Please note!
• Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the Instruction for use in the section “Setting
water hardness (page 15).
Follow the instructions:
1. Remove the water tank, fill to the MAX line with fresh
water (fig. 1A) then put back in the appliance (fig. 1B).
2. Place a container with a minimum capacity of 100 ml
under the cappuccino maker (fig. 2).
3. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the I position
(fig. 3).
4. The light flashes on the control panel (fig. 4).
5. 5. Turn the steam dial to the “
I ” position (fig. 5). The ap-
pliance delivers water from the cappuccino maker then
goes off.
6. Turn the steam dial to the “0” position.
The coffee maker is now ready for normal use.
Please note!
• When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before it starts
to give satisfactory results.
• To enjoy your coffee even more and improve the perfor-
mance of your appliance, we recommend installing a water
softener filter as described in the section “ WATER SOFTE-
NER FILTER “ (page 10). If your model is not provided
with a filter, you can request one from De’Longhi Customer
Services.
TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch is
pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
• To turn the appliance on, press the (fig. 6): The corre-
sponding light flashes while the appliance is heating
up and performing an automatic rinse cycle (by circulating
hot water, the appliance heats both the boiler and the in-
ternal circuits).
The appliance is at temperature when the light goes off and
the lights corresponding to the coffee buttons come on.