background image

9

Caution! 
The range becomes very hot during operation.
Keep children well out of reach.

LIGHTING GAS BURNERS FITTED WITH FLAME FAILURE
SAFETY DEVICE (Semi-rapid and triple ring)

In order to light the burner, you must:

1 – Push and turn the knob in an anti-clockwise direction up to the 

position

(maximum rate), push in and hold the knob until the flame has been lit (fig. 2.2).

The sparks produced by the lighter situated inside the relative burner will light the
flame. 

In the event that the local gas supply conditions makes it difficult to light the burn-
er in 

position, try again with the knob in 

position.

If there is no mains electrical supply, bring a lighted match close to the burner. 

2 – Wait for about ten seconds after the gas burner has been lit before letting go the

knob (safety device activation delay).

3 – Adjust the gas valve to the desired position.

If the burner flame should go out for some reason, the safety valve will automatically
stop the gas flow.

To re-light the burner, return the knob to the closed 

position, 

wait for at least 1

minute

and then repeat the lighting procedure. 

If your local gas supply makes it difficult to light the burner with the knob set to maxi-
mum, set the knob to minimum and repeat the operation.

Содержание DESFGG 36 D Series





























Отзывы: