Dell Vostro 3580 Скачать руководство пользователя страница 5

Страница: 5 / 90

Installing the display cable............................................................................................................................................. 81

Display back-cover and antenna assembly...................................................................................................................... 82

Removing the display back-cover............................................................................................................................... 82
Installing the display back-cover..................................................................................................................................84

Palm-rest and keyboard assembly.................................................................................................................................... 85

Removing the palmrest and keyboard assembly....................................................................................................... 85

4 Troubleshooting......................................................................................................................... 87

Enhanced Pre-Boot System Assessment (ePSA) diagnostics......................................................................................87

Running the ePSA diagnostics..................................................................................................................................... 87

5 Getting help.............................................................................................................................. 90

Contacting Dell.................................................................................................................................................................... 90

Contents

Содержание Vostro 3580



























































































Результаты поиска

Содержание Vostro 3580

Отзывы:

Бренды по названию

Популярные бренды

Dell Vostro 3580, Руководство по обслуживанию

Результаты поиска

Содержание Vostro 3580

Отзывы:

Бренды по названию

Популярные бренды