manualshive.com logo in svg

Dell Vostro 3580, Руководство по обслуживанию

Поделиться
Скачать
Dell Vostro 3580 Скачать руководство пользователя страница 81

5. Remove the 

battery

6. Remove the 

WLAN

7. Remove the 

SSD

8. Remove the 

hard drive assembly

9. Remove the 

system fan

10. Remove the 

heatsink

11. Remove the 

display assembly

12. Remove the 

display bezel

13. Remove the 

display panel

14. Remove the 

display hinges

Steps

1. Disconnect the camera cable on the display back-cover and antenna assembly [1].
2. Peel the adhesive that secures the camera cable [2].
3. Remove the camera cable and the display cable from the routing guides on the display back-cover and antenna assembly[3]

Installing the display cable

Steps

1. Route the camera cable through the routing guides on the display back-cover and antenna assembly [1].
2. Affix the adhesive that secures the camera cable [2].
3. Connect the camera cable on the display back-cover and antenna assembly [3].

Removing and installing components

81

Содержание Vostro 3580



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды