Dell S2721NX Скачать руководство пользователя страница 12

  5. Trouble Shooting Instructions

Common problems

The following table contains general information about common monitor problems you 
might encounter and the possible solutions.

Common 
symptoms

What you 
experience

Possible solutions

No video/
Power LED off

No picture

• Ensure that the video cable connecting the 

monitor and the computer is properly connected 
and secure.

• Verify that the power outlet is functioning 

properly using any other electrical equipment.

• Ensure that the power button is depressed fully.
• Ensure that the correct input source is selected 

in the 

Input Source

 menu.

No video/
Power LED on

No picture or no 
brightness

• Increase brightness and contrast controls 

through OSD.

• Perform monitor self-test feature check.
• Check for bent or broken pins in the video cable 

connector.

• Run the built-in diagnostics.
• Ensure that the correct input source is selected 

in the 

Input Source

 menu.

Missing pixels

LCD screen has 
spots

• Cycle power on-off.
• Pixel that is permanently off is a natural defect 
   that can occur in LCD technology.
• For more information about Dell Monitor Quality 
  and Pixel Policy, see Dell Support site at: 
  

 https://www.dell.com/support/monitors

.

Stuck-on pixels LCD screen has 

bright spots

• Cycle power On-Off.
• Pixel that is permanently off is a natural defect  
   that can occur in LCD technology.
• For more information about Dell Monitor Quality 
   and PixelPolicy, see Dell Support site at: 
   

https://www.dell.com/support/monitors

.

Содержание S2721NX















Отзывы: