Dell PowerEdge M600 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 236

background image

42

About Your System

I/O Connectivity

The M1000e enclosure

supports three layers of I/O fabric, selectable between

combinations of Ethernet, Infiniband, and fibre-channel modules. (Additional
fabrics including10 Gb Ethernet will be supported in the future.) You can install
up to six hot-swappable I/O modules in the enclosure, including fibre-channel
switches, fibre-channel pass-throughs, Infiniband switches, Ethernet switches,
and Ethernet pass-through modules

.

Guidelines for Installing I/O Modules

You must follow these guidelines when populating I/O modules. See
Figure 1-9 for the I/O bay locations.

General I/O Module Configuration Guidelines

•

If an I/O module is installed in Fabric B or Fabric C, at least one blade
must have a matching mezzanine card installed to support data flow for
that I/O module.

•

If a blade has an optional mezzanine card installed in a Fabric B or Fabric
C card slot, at least one corresponding I/O module must be installed to
supported data flow for that fabric

•

Within each fabric type, you must install a module in the fabric’s channel
1 slot before installing a module in the fabric’s channel 2 slot. For example,
you must install a module in slot C1 before installing a module in slot C2.

•

Modules may be installed in Fabrics B and C independently (you do not
need to install modules in Fabric B before installing modules in the Fabric
C slots.)

•

Slots A1 and A2 only support Ethernet I/O modules. This fabric type is
hard-set to Ethernet for these slots and cannot support Fibre Channel,
Infiniband, or other fabric type modules.

•

Slots A, B, and C can support Ethernet fabric-type modules.

•

To enable switch configuration prior to blade imaging, I/O modules are
allowed to power-up before a blade is inserted in the enclosure.

«
...
40
41
42
43
44
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

Бренд: Harmonic Страницы: 56

Бренд: Vivotek Страницы: 136

Бренд: Oracle Страницы: 24

Бренд: MiLAN Страницы: 1

PacketShaper PS-S200

Бренд: Symantec Страницы: 2

Бренд: Roland Страницы: 2

Бренд: Realtek Страницы: 30

Бренд: Gate Страницы: 8

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: Lanner Страницы: 59

Бренд: Raven Страницы: 33

Бренд: Laser Страницы: 4

Бренд: Kaya Instruments Страницы: 48

MTDOT-868 Series

Бренд: Multitech Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды