Dell PowerConnect J-8216 Скачать руководство пользователя страница 153

Страница: 153 / 270

To connect a J-EX Series switch to a management console (see Figure 64 on page 137
and Figure 65 on page 137):

Connect one end of the Ethernet cable into the console port (labeled

CON

CONSOLE

) on the J-EX Series switch.

For the location of the

CON/CONSOLE

port, see “Routing Engine (RE) Module in a

J-EX8216 Switch” on page 26.

Connect the other end of the Ethernet cable into the console server (see Figure 64 on
page 137) or management console (see Figure 65 on page 137).

To configure the switch from the management console, see“Connecting and Configuring
a J-EX Series Switch (CLI Procedure)” on page 144 or “Connecting and Configuring a J-EX
Series Switch (J-Web Procedure)” on page 146.

Figure 64: Connecting a J-EX Series Switch to a Management Console
Through a Console Server

Figure 65: Connecting a J-EX Series Switch Directly to a Management
Console

Documentation

Connecting a J-EX Series Switch to a Network for Out-of-Band Management on page 135

•

Console Port Connector Pinout Information for a J-EX Series Switch on page 49

•

Cables Connecting the J-EX8200 Switch to Management Devices on page 77

Connecting a J-EX Series Switch to a Modem

You can connect a J-EX Series switch to a modem through the console port on the switch.

Before you connect the switch to a modem:

•

Perform the initial setup and configuration of the switch. See “Connecting and
Configuring a J-EX Series Switch (CLI Procedure)” on page 144 or “Connecting and
Configuring a J-EX Series Switch (J-Web Procedure)” on page 146.

Ensure that you have the following parts available before you begin to connect the switch
to the modem:

137

Chapter 10: Connecting the Switch

Содержание PowerConnect J-8216















































































































































































































































































Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect J-8216, Руководство по оборудованию

Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды