Dell Latitude 3000 Series Скачать руководство пользователя страница 44

Страница: 44 / 79

Removing the heat sink

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/

regulatory_compliance.

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

CAUTION:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils

in your skin can reduce the heat transfer capability of the thermal grease.

Topics:

•

Prerequisites

•

Procedure

Prerequisites

1. Remove the

battery

2. Follow the procedure from step 1 to step 3 in “

Removing the optical drive

”.

3. Remove the

keyboard

4. Follow the procedure from step 1 to step 5 in “

Removing the base cover

”.

Procedure

1. Remove the screws that secure the heat sink to the system board.
2. Slide to release the heat sink from the tab on the display hinge.
3. Lift the heat sink off the system board.

Removing the heat sink

Содержание Latitude 3000 Series
















































































Результаты поиска

Содержание Latitude 3000 Series

Отзывы:

Похожие инструкции для Latitude 3000 Series

Бренды по названию

Популярные бренды

Dell Latitude 3000 Series, Руководство по обслуживанию

Результаты поиска

Содержание Latitude 3000 Series

Отзывы:

Похожие инструкции для Latitude 3000 Series

Бренды по названию

Популярные бренды