background image

4

System Setup

System Setup enables you to manage your computer hardware and specify BIOS

level options. From the 

System Setup, you can:

• Change the NVRAM settings after you add or remove hardware
• View the system hardware configuration
• Enable or disable integrated devices
• Set performance and power management thresholds
• Manage your computer security

Boot Sequence

Boot Sequence allows you to bypass the System Setup

defined boot device order and boot directly to a 

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the 
Dell logo appears, you can:

• Access System Setup by pressing <F2> key
• Bring up the one-time boot menu by pressing <F12> key

The one-time boot menu displays the devices that you can boot from including the diagnostic option. 
The boot-menu options are:

• Removable Drive (if available)
• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive
• Diagnostics

NOTE: Choosing Diagnostics, will display the 

ePSA diagnostics

 screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation Keys

The following table displays the system setup navigation keys.

NOTE: For most of the system setup options, changes that you make are recorded but do not take 
effect until you re-start the system.

54

Содержание Latitude 14 Rugged Extreme







































































Отзывы: