manualshive.com logo in svg

Dell Inspiron X200, Руководство по обслуживанию

Поделиться
Скачать
Dell Inspiron X200 Скачать руководство пользователя страница 59

Battery Latches: Dell Latitude X200 Service Manual

Back to Contents Page

 

Battery Latches 

Dell™ Latitude™ X200 Service Manual

Removing the Battery Latches 

NOTICE: 

Disconnect the computer and any attached devices from electrical 

outlets. 

NOTICE: 

To avoid ESD, ground yourself by using a wrist grounding strap or by 

touching an unpainted metal surface on the computer. 

NOTICE: 

Read "

Preparing to Work Inside the Computer

" before performing the 

following procedure. 

1.  Remove the 

battery

. 

2.  Remove the 

keyboard

. 

3.  Remove the 

palm rest

. 

4.  Remove the 

hinge covers

. 

5.  Remove the 

display assembly

. 

6.  Remove the 

keyboard tray

. 

7.  Remove the 

hard drive

. 

8.  Remove the 

memory module

. 

9.  Remove the 

Mini PCI card

, if present. 

10.  Remove the 

system board

. 

11.  On the inside of the bottom case, use your fingers to unhook the latch from the 

bottom case and the snap tabs, catching the latch button on the outside of the 

bottom case. 

file:///F|/Service%20Manuals/Dell/Latitude/x200/batlatch.htm (1 of 3) [2/28/2004 8:24:06 AM]

Содержание Inspiron X200









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды