Dell Inspiron X200 Скачать руководство пользователя страница 4

Страница: 4 / 72

Before You Begin: Dell Latitude X200 Service Manual

5. Disconnect the computer from the electrical outlet.

6. To avoid possible damage to the system board, wait 10 to 20 seconds and then

disconnect any attached devices.

7. Disconnect all other external cables from the computer.

8. Remove any installed PC Cards or plastic blanks from the PC Card slot.

9. Close the display and turn the computer upside down on a flat work surface.

NOTICE:

To avoid damaging the system board, you must remove the battery

before you service the computer.

10. Remove the battery from the battery bay.

11. To dissipate any static electricity while you work, use a wrist grounding strap or

periodically touch an unpainted metal surface.

12. Handle components and cards with care. Do not touch the components or

contacts on a card. Hold a card by it edges or by its metal mounting bracket.

Hold a component such as a microprocessor by its edges, not by its pins.

Recommended Tools

The procedures in this manual require the following tools:

●

#1 magnetized Phillips screwdriver

●

¼-inch flat-blade screwdriver

●

Small plastic scribe

Computer Orientation

file:///F|/Service%20Manuals/Dell/Latitude/x200/begin.htm (2 of 6) [2/28/2004 8:23:54 AM]

Содержание Inspiron X200









































































Результаты поиска

Содержание Inspiron X200

Отзывы:

Бренды по названию

Популярные бренды

Dell Inspiron X200, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron X200

Отзывы:

Бренды по названию

Популярные бренды