Dell Inspiron 7591 2-in-1 Скачать руководство пользователя страница 44

Страница: 44 / 80

Replacing the heat sink

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Incorrect alignment of the heat sink can damage the system board and processor.

NOTE:

If either the system board or the heat sink is replaced, use the thermal pad/paste provided in the kit to ensure

that thermal conductivity is achieved.

Procedure

1. Align the screw holes on the heat sink with the screw holes on the system board.
2. In sequential order (as indicated on the heat sink), tighten the four captive screws that secure the heat sink to the system board.

Removing and installing components

Содержание Inspiron 7591 2-in-1

















































































Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды

Dell Inspiron 7591 2-in-1, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды