Dell Inspiron 7591 2-in-1 Скачать руководство пользователя страница 18

Страница: 18 / 80

2. Align the notch on the memory module with the tab on the memory-module slot.
3. Slide the memory module firmly at an angle, into the memory-module slot.
4. Press the memory module down until it clicks into place.

NOTE:

If you do not hear the click, remove the memory module and reinstall it.

Post-requisites

Replace the

base cover

Wireless card

Removing the wireless card

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Removing and installing components

Содержание Inspiron 7591 2-in-1

















































































Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды

Dell Inspiron 7591 2-in-1, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды