manualshive.com logo in svg

Dell Inspiron 3670, Руководство по обслуживанию, Страница: 56 / 76

Поделиться
Скачать
Dell Inspiron 3670 Скачать руководство пользователя страница 56

Replacing the system board

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer and follow the 

steps in 

Before working inside your computer

. After working inside your computer, follow the instructions in 

After working inside 

your computer

. For more safety best practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

NOTE: 

Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program 

after you replace the system board.

NOTE: 

Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You must 

make the appropriate changes again after you replace the system board.

 

Topics:

•

Procedure

•

Post-requisites

Procedure

NOTE: 

To ensure that cables are connected to the correct system board connectors, see “

System board components

’.

NOTE: 

Depending on the configuration ordered your computer may have up to two 2.5-inch hard-drives installed. If only one 

hard-drive is installed skip step 9 or step 11 where applicable.

1 

Slide the edge of the system board into the front-I/O slot on the chassis and lower the system board into the chassis.

2 

Align the screw holes on the system board with the screw holes on the on the chassis.

33

56

Replacing the system board

Содержание Inspiron 3670













































































Отзывы:

Нет отзывов