Dell Inspiron 15 5000 Series Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 121

background image

7

Select the device from the left pane and click

Run Tests

.

8

If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.

System diagnostic lights

Power and battery-status light/hard-drive activity light

Indicates the battery-charge status or the hard-drive activity.

NOTE: Press Fn+H to toggle this light between power and battery-status
light and hard-drive activity light.

Hard-drive activity light

Turns on when the computer reads from or writes to the hard drive.

NOTE: Hard-drive activity light is supported only on computers shipped with
hard drive.

Power and battery-status light

Indicates the power and battery-charge status

Solid white

— Power adapter is connected and the battery has more than 5 percent

charge.

Amber

— Computer is running on battery and the battery has less than 5 percent

charge.

Off

•

Power adapter is connected and the battery is fully charged.

•

Computer is running on battery and the battery has more than 5 percent charge.

•

Computer is in sleep state, hibernation, or turned off

NOTE: Hard-drive activity light is supported only on computers shipped with
hard drive.

The power and battery-status light blinks amber along with beep codes indicating
failures.
For example, the power and battery-status light blinks amber two times followed by a
pause, and then blinks white three times followed by a pause. This 2,3 pattern
continues until the computer is turned off indicating no memory or RAM is detected.
The following table shows different light patterns and describes what they indicate.

117

«
...
115
116
117
118
119
...
»

Содержание Inspiron 15 5000 Series


























































































































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 15 5000 Series

Бренд: Panasonic Страницы: 13

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 112

Бренд: Panasonic Страницы: 40

Бренд: Panasonic Страницы: 192

Toughbook CF-T7BWATAAM

Бренд: Panasonic Страницы: 44

Toughbook CF-F8EWDZZAM

Бренд: Panasonic Страницы: 20

Toughbook CF-19CHBAXBM

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 40

The Toughbook 52

Бренд: Panasonic Страницы: 2

Бренд: Gateway Страницы: 87

Бренд: IBM Страницы: 94

Бренд: IBM Страницы: 102

Бренд: IBM Страницы: 96

Бренд: IBM Страницы: 96

Бренд: IBM Страницы: 98

Бренд: IBM Страницы: 178

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды