Dell Inspiron 14 N4120 Скачать руководство пользователя страница 21

Страница: 21 / 106

Optical Drive

Replacing the Optical Drive

Follow the instructions in "Before You Begin" on page 9.

Align the tabs on the optical-drive bezel with the slots on the optical drive

and snap the optical-drive bezel into place.

Align the screw holes on the optical-drive bracket with the screw holes on

the optical drive and replace the two screws.

Slide the optical-drive assembly into the optical-drive compartment until

it is fully seated.

Replace the screw that secures the optical-drive assembly to the computer

base.

Replace the module cover (see "Replacing the Module Cover" on page 18).

Replace the battery (see "Replacing the Battery" on page 16).

CAUTION:

Before turning on the computer, replace all screws and ensure that no

stray screws remain inside the computer. Failure to do so may result in damage to
the computer.

screws (2)

optical-drive bracket

optical drive

optical-drive bezel

Содержание Inspiron 14 N4120











































































































Результаты поиска

Содержание Inspiron 14 N4120

Отзывы:

Похожие инструкции для Inspiron 14 N4120

Бренды по названию

Популярные бренды

Dell Inspiron 14 N4120, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 14 N4120

Отзывы:

Похожие инструкции для Inspiron 14 N4120

Бренды по названию

Популярные бренды