background image

 

 

1.

Remove the new Mini-Card from its packing.  
 

 

 

 

 

2.

Insert the Mini-Card at a 45-degree angle into the appropriate system board connector. For example, the WLAN card connector is labeled WLAN and so 
on.  
 

 

  

3.

Press the other end of the WLAN card down into the slot on the system board and replace the two securing screws.  
 

 

  

4.

Connect the appropriate antenna cables to the Mini-Card you are installing. The following table provides the antenna cable color scheme for each Mini-
Card supported by your computer.  
 

 

 

5.

Secure unused antenna cables in the protective mylar sleeve.  
 

 

  

6.

Replace the keyboard (see 

Replacing the Keyboard

).  

 

 

  

7.

Replace the battery (see 

Replacing the Battery

).  

 

 

  

8.

Install the drivers and utilities for your computer, as required. For more information, see the 

Dell Technology Guide

.  

 

Back to Contents Page

 

 

 

 

CAUTION: 

Use firm and even pressure to slide the card into place. If you use excessive force, you may damage the connector.

Connectors on the Mini-Card 

Antenna Cable Color Scheme 

WWAN (2 antenna cables)

 

Main WWAN (white triangle) 

Auxiliary WWAN (black triangle) 

 

 

white with gray stripe 

black with gray stripe 

WLAN (2 antenna cables)

 

Main WLAN (white triangle) 

Auxiliary WLAN (black triangle) 

 

 

white 

black 

 

NOTE: 

If you are installing a communication card from a source other than Dell, you must install the appropriate drivers and utilities. For more generic 

driver information, see the 

Dell Technology Guide

.

Содержание Inspiron 1010













































Отзывы: