Dell FS7500 Скачать руководство пользователя | Manualshive

Страница: 51 / 88

background image

EqualLogic FS7500 Installation and Setup

4 Network Cable Connections

Figure 39: Securing the Signal and Power Cable Bundles

Steps for Managing Cables Using a Service Loop

A service loop is an extra length of cable between the rear of the rack and the controller. Using a service loop
allows you to extend the controller forward on its rails for servicing without needing to disconnect all of the
cables from the back panel of the controller.

Note:

Servicing a controller installed with a service loop requires at least two individuals one at the front of the

rack and one at the back.

The procedure to install a service loop consists of the following steps:

•

Make sure that the signal and power cables are properly connected to the controller back panel.

•

Extend the controller forward from the rack into the service position

•

Route the power cables through the strain relief straps

•

Bundle the signal and power cables together using the hook-and-loop fasteners supplied in the shipping box

•

Secure the signal and power cable bundles to the rails

•

Slide the controller back into the rack

Routing the Power Cables Through the Strain Relief Straps

See

Routing the Power Cables Through the Strain Relief Straps on page 42

for the procedure.

Note:

Using strain relief with the power cables in this installation prevents the controller from being powered

down accidentally during servicing.

45

«
...
49
50
51
52
53
...
»

Содержание FS7500

























































































Отзывы:

Нет отзывов

Похожие инструкции для FS7500

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Бренд: 2N Страницы: 11

Бренд: 2N Страницы: 5

Бренд: 2N Telekomunikace Страницы: 24

Бренд: IBM Страницы: 32

Бренд: A10 Страницы: 52

Бренд: Measurement Computing Страницы: 27

Бренд: FDI Страницы: 2

Бренд: Digi Страницы: 116

ADSL2+ Wireless MIMO Router

Бренд: Ace Страницы: 64

BPTA-CPUMS-V2-SKA

Бренд: Bitspower Страницы: 6

LonWorks Communication Module LN-01

Бренд: Delta Electronics Страницы: 1

Бренд: ZALMAN Страницы: 18

Бренд: AMD Страницы: 45

Бренд: Maipu Страницы: 19

Бренд: Cypress Semiconductor Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды