Dell EMC VNXe Series Скачать руководство пользователя страница 17

Страница: 17 / 52

System component description

Overview

Table 1

describes the VNXe3100 platform 2U DPE and the disk drive status LEDs.

Rear view

On the rear, the VNXe3100 platform includes one of two versions of the following
hardware components:

◆

One 2U DPE with a single storage processor (SP A):

• One SP

• Two power supply modules

• One Cache Protection Module; 1 GB

◆

One 2U DPE with two storage processors (SP A and B):

• Two SPs

• Two power supply modules

Note: In the following sections, the illustrations and corresponding tables describe these
individual components. These descriptions are for illustrative purposes only.

Table 1 VNXe3100 platform 2U, 12 (3.5-inch) DPE and disk drive LEDs

LED

Color

State

Description

DPE power (location 2)

Blue

Powering and powered up

—

Off

Powered down

Disk drive ready/activity

(location 3)

Note: The disk drive LED (a
left or right triangle symbol)
points to the disk drive that
it refers to.

Blue

Powering and powered up

Blinking, mostly

Disk drive is on with I/O activity

Blinking at

constant rate

Disk drive is spinning up or down

normally

Blinking, mostly

off

Disk drive is powered up but not

spinning

Note: This is a normal part of the
spin-up sequence, occurring
during the spin-up delay of a
slot.

—

Off

Disk drive is powered down

Содержание EMC VNXe Series





















































Результаты поиска

Содержание EMC VNXe Series

Отзывы:

Похожие инструкции для EMC VNXe Series

Бренды по названию

Популярные бренды

Dell EMC VNXe Series, Руководство по аппаратным средствам

Результаты поиска

Содержание EMC VNXe Series

Отзывы:

Похожие инструкции для EMC VNXe Series

Бренды по названию

Популярные бренды