Dell EMC PowerSwitch Z9432F-ON Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 53

background image

Check your switch

To confirm that ONIE is working properly, use the

onie-sysinfo

command. Run the

onie-sysinfo

command at the ONIE

prompt.

ONIE:/ # onie-sysinfo x86_64-dell_<

platform

>_c25

ONIE:/ # onie-sysinfo –v (ONIE Version programmed)

3.23.1.0

ONIE:/ #

ONIE:/ # uname -a

Linux onie 3.2.35-onie+ #1 SMP Tue Dec 9 17:08:16 PST 2014 x86_64 GNU/Linux ONIE:/ #

ONIE:/ #

ONIE service discovery

ONIE attempts to locate the installer through several discovery methods.

To download and run an installer, the ONIE Service Discovery feature follows these steps in order and uses the first successful
method found:
1. Search locally attached storage devices for one of the ONIE default installer filenames—for example,

onie self update

from the USB.

2. Discover TFTP-based image from the DHCP server.
3. Query to the IPv6 link-local neighbors using HTTP for an installer.

If none of the ONIE Service Discovery methods are successful, you can disable this using the

onie-discovery-stop

command.

You can install an operating system manually from HTTP, FTP, or TFTP using the

onie-nos-install <URL>

command.

NOTE:

If you have a recovery USB plugged into your switch, you must uninstall it before using the

onie-nos-install

command.

The ONIE Install environment uses DHCP to assign an IP address to the management interface—eth0. If that fails, it uses the
default IP address 192.168.3.10/255.255.255.0.

To display the IP address, use the

ifconfig eth0

command, as shown.

ONIE:/ # ifconfig eth0

eth0 Link encap:Ethernet HWaddr 90:B1:1C:F4:9C:76

inet addr:xx.xx.xx.xx Bcast:xx.xxx.xxx.xxx Mask:xxx.x.x.x

inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:18 errors:0 dropped:0 overruns:0 frame:0

TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000

RX bytes:1152 (1.1 KiB) TX bytes:6864 (6.7 KiB)

Interrupt:21 Memory:ff300000-ff320000

To assign an IP address to the management interface, eth0, and verify network connectivity, use the

ifconfig eth0

<ip

address>

command, as shown.

ONIE:/ # ifconfig eth0 xx.xx.xx.xx/xx up

Verify the network connection with ping.

ONIE:/ # ping xx.xx.x.xx

PING xx.xx.x.xx (xx.xx.x.xx): 56 data bytes

64 bytes from xx.xx.x.xx: seq=0 ttl=62 time=1.357 ms

64 bytes from xx.xx.x.xx: seq=1 ttl=62 time=0.577 ms

^C

46

Before you install an operating system

«
...
44
45
46
47
48
...
»

Содержание EMC PowerSwitch Z9432F-ON






















































Отзывы:

Нет отзывов

Похожие инструкции для EMC PowerSwitch Z9432F-ON

Бренд: Tecsis Страницы: 2

S5130S-EI series

Бренд: H3C Страницы: 67

Бренд: FCI Страницы: 78

velatia cgm.3 system

Бренд: Ormazabal Страницы: 76

Бренд: Metra Electronics Страницы: 8

Бренд: Xantech Страницы: 12

Бренд: Exsys Страницы: 14

Бренд: Foxun Страницы: 10

Бренд: ATEN Страницы: 303

Бренд: FS Страницы: 40

Бренд: C4i Страницы: 22

Бренд: StarTech.com Страницы: 2

Бренд: Panasonic Страницы: 19

Бренд: Palmer Страницы: 4

SmartSTACK 10 ELS10-26

Бренд: Cabletron Systems Страницы: 18

Бренд: Epson Страницы: 2

Elinx EIR508-2MC-T

Бренд: B&B Electronics Страницы: 2

UltraLink UL-DV3

Бренд: Rose electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды