Dell 4PM34 Скачать руководство пользователя страница 61

Страница: 61 / 150

Optional front bezel

The front bezel is attached to the front of the system to prevent unauthorized access to the system peripherals. The front bezel can be
locked for additional security.

Removing the front bezel

Prerequisite

Follow the safety guidelines listed in

Safety instructions

Steps

Unlock the bezel by using the bezel key.

NOTE:

There are two bezel keys attached to the back of the bezel.

Press the release latch at the top of the bezel.

Pull the top end of the bezel away from the system.

Unhook the bezel tabs from the slots at the bottom of the system, and pull the bezel away from the system.

Figure 13. Removing the front bezel

Installing the front bezel

Prerequisite

Follow the safety guidelines listed in

Safety instructions

Steps

Locate and remove the bezel key.

NOTE:

There are two bezel keys attached to the back of the bezel.

Insert the bezel tabs into the slots in the chassis.

Press the release latch, and push the bezel toward the system until the bezel locks into place.

Installation and Service Manual

Installing and removing system components

Содержание 4PM34























































































































































Результаты поиска

Содержание 4PM34

Отзывы:

Похожие инструкции для 4PM34

Бренды по названию

Популярные бренды

Dell 4PM34, Руководство пользователя

Результаты поиска

Содержание 4PM34

Отзывы:

Похожие инструкции для 4PM34

Бренды по названию

Популярные бренды