Dell 302-004-341 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 70

background image

Networking connectivity architecture and cabling best
practice (R640, R740XD servers)

This topic describes connectivity architecture, cabling best practice information, and
cable connection examples from typical ScaleIO Ready Node configurations in order to
help you plan your network.

Note

If you are not familiar with ScaleIO system architecture, refer to "System
Architecture" in the

ScaleIO User Guide

or

ScaleIO Deployment Guide

.

Note

ScaleIO uses APIPA IP addresses (169.254.x.x/16) for Broadcast and Unicast, and this
requires special configuration during deployment.

It is mandatory to set the Management VLAN as either a Layer 2 VLAN without an IP
address, or as VLAN 0 (meaning, no VLAN). This will facilitate a seamless onsite "Add
Node" operation.

Network prerequisites

Ensure that you have the following network resources and equipment available before
installing ScaleIO Ready Node servers.

Note

In addition to the requirements below for connecting ScaleIO Ready Node servers to
one or more switches, ensure that you have prepared the items described in

on page 14 .

Switches

One 10 GbE switch is required. Two or more 10 GbE switches may be used for
high availability and load balancing purposes. Separate (one or more) 1 GbE
switches may be used for the management network.
Before you begin connecting the switches, ensure that they are installed and
configured. Do not connect the switches to your organization's network until all
installation and configuration activities are complete.

Note

Each node has four 10 GbE ports. Two are used by for internal network
communication. The other two ports are used for VMware high availability, DRS,
and client network traffic.

The switches must have sufficient available network ports to accommodate the
following:

l

Data network 10 GbE switches: Two, 10 GbE ports per node, per switch

l

Management network switches: One, 1 GbE and one BMC (iDRAC) port per
node.

Network Architecture and Physical Connectivity

30

Hardware Configuration and Operating System Installation Guide - Windows Servers

«
...
28
29
30
31
32
...
»

Содержание 302-004-341







































































Отзывы:

Нет отзывов

Похожие инструкции для 302-004-341

SX-2000A Series

Бренд: GDC Страницы: 185

Бренд: Black Box Страницы: 30

Бренд: Lexmark Страницы: 76

Бренд: Lexmark Страницы: 134

System x3300 M4

Бренд: IBM Страницы: 52

DIGIARRAY DA-4000E

Бренд: Digiever Страницы: 9

Бренд: Obvius Страницы: 39

Бренд: IBM Страницы: 8

PowerEdge C6420

Бренд: Dell EMC Страницы: 53

Бренд: Dell EMC Страницы: 110

PowerEdge FC430

Бренд: Dell EMC Страницы: 117

Бренд: Dell EMC Страницы: 174

Бренд: Aastra Страницы: 250

Бренд: ZeeVee Страницы: 73

BladeCenter HX5

Бренд: IBM Страницы: 142

Бренд: Ganz Страницы: 128

Бренд: Calmotion Страницы: 8

Turbo NAS TDS-16489U

Бренд: QNAP Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды