Dell EMC VNXe3100 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 14

background image

This document describes how to add a second storage processor (SP) to a VNXe3100 or
VNXe3150 disk processor enclosure (DPE).

Before you start

Before you begin the upgrade procedure

:

◆

Make sure you have a current backup of your system data before you begin this (or any

other) upgrade procedure.

◆

Make sure your VNXe system is running Maintenance Release 1 Service Pack 1

(version 2.1.1) or later. See the Unisphere online help for information about updating
your system software.

◆

Make sure you have a new storage processor available to replace the cache protection

module, four 4 GB memory modules, and any I/O module required to match the
current SP. You also need appropriate network and SAS cabling to duplicate the
connections to SP A.

◆

Refer to your EMC VNXe online help (Servicing your system > Adding or replacing

faulted hardware components > Add a new hardware component) for instructions on
how to handle hardware components. Take particular care to review the instructions
on avoiding electrostatic discharge (ESD).

IMPORTANT

Since the procedure to upgrade from a single SP to two SPs involves reboots and the
temporary quiescence of the sole processor, your system will not process or make
available any data until the procedure is finished. Plan you upgrade accordingly.

EMC

®

VNXe3100/VNXe3150

Adding a Second Storage Processor

P/N 300-012-179
REV 03

1
2
3
...
»

Содержание VNXe3100















Отзывы:

Нет отзывов

Похожие инструкции для VNXe3100

Бренд: ZALMAN Страницы: 7

Бренд: Altelix Страницы: 2

WHAD HE 3 101 66

Бренд: LEGRAND Страницы: 100

Бренд: StarTech.com Страницы: 13

Бренд: Vectronics Страницы: 4

Бренд: SCC Страницы: 47

Бренд: Icy Box Страницы: 32

Бренд: OBERON Страницы: 2

Бренд: StarTech.com Страницы: 13

Бренд: UFO Страницы: 20

Бренд: TOOQ Страницы: 22

Бренд: TOOQ Страницы: 26

Бренд: TOOQ Страницы: 30

Бренд: NavePoint Страницы: 2

U457-1M2-SATAG2

Бренд: Tripp Lite Страницы: 32

Бренд: Calix Страницы: 44

Бренд: Dantherm Страницы: 76

Smart Backup HDD-Enclosure

Бренд: Hama Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды