background image

List of Figures

Figure 1. A10 sliding rail assembly - 1U systems.................................................................................................. 7

Figure 2. Installing the rear end of the rail........................................................................................................... 8

Figure 3. Installing the front end of the rail......................................................................................................... 8

Figure 4. Installing screws......................................................................................................................................9

Figure 5. Extend rails from the cabinet................................................................................................................9

Figure 6. Install the system in the rails............................................................................................................... 10

Figure 7. Slide the system into the cabinet........................................................................................................10

Figure 8. Installing the front bezel on 1U system............................................................................................... 11

Figure 9. CMA bracket slots................................................................................................................................ 12

Figure 10. Node with RJ-45 iDRAC connection................................................................................................ 12

Figure 11. F200 and F600 node LCD display......................................................................................................16

4

List of Figures

Содержание PowerScale F200




















Отзывы: