background image

Part Number: 9295093A  02/21

 DANGER

Installation must comply with all applicable fire and 

health codes in your jurisdiction.

 DANGER

Use appropriate safety equipment during installation and 

servicing.

n

Warning

Do not damage the refrigeration circuit when installing, 

maintaining or servicing the unit.

Location

n

Warning

This equipment must be positioned so that the plug is 

accessible unless other means for disconnection from the 

power supply (e.g., circuit breaker or disconnect switch) 

is provided.

n

Warning

Adequate means must be provided to limit the movement 

of this appliance without depending on or transmitting 

stress to the electrical conduit or gas lines. 

n

Warning

To avoid instability the installation area must be capable 

of supporting the combined weight of the equipment 

and product. Additionally the equipment must be level 

side to side and front to back.

n

Warning

This equipment is intended for indoor use only. Do not 

install or operate this equipment in outdoor areas.

The location selected for the equipment must meet the 

following criteria. If any of these criteria are not met, select 

another location.
•  Units are intended for indoor use only.
•  The location MUST be level, stable and capable of 

supporting the weight of the equipment.

•  The location MUST be free from and clear of combustible 

materials.

•  Equipment MUST be level both front to back and side to 

side.

•  Position the equipment so it will not tip or slide.
•  Front casters MUST be locked once positioned.
•  Recommended air temperature is 50° - 100°F 

(10° - 38°C).

•  Proper air supply for ventilation is REQUIRED AND 

CRITICAL for safe and efficient operation.

•  Do not obstruct the flow of ventilation air. Make sure the 

air vents of the equipment are not blocked.

•  Do not install the equipment directly over a drain. Steam 

rising up out of the drain will adversely affect operation, 

air circulation, and damage electrical / electronic 

components.

Section 2

Installation

Содержание ST4427NP-6





























Отзывы: