background image

GENERAL  W

ARNING

GENERAL W

ARNING

6

Freephone

. 0508 782 753  

|

  

Email

[email protected] 

Model

NACP-400990

Input Voltage Range

100-240 VAC

Input Frequency

50/60 or 50/60Hz

Efficiency

75% typ

Leakage Current

0.35mA max

Pre-Charge Current

0.15A-0.25A

Pre-Charge Voltage

4V<V battery<6V

Complete Charge

2A

Constant Voltage

8.2V – 8.4V

Complete Charge

<0.15A typ

Total Charge Time

2 Hours max

Overvoltage Protection

8.5V typ

Work Temperature

0°C – 50°C

Battery Pack Temperature Protection

T < 0°C or T > 55°C

Continuous Power Output

17W max

 

Charger Safety Warning 

 

 

• 

Do not use the charger in an explosive atmosphere. The electrical device is not  

 

 

designed for use in such environments.

 

• 

Do not charge the battery outdoors or in temperatures below 5˚C (40˚F).

 

• 

Do not puncture or attempt to open battery case or cells.

 

• 

Do not immerse the charger into water or other fluid. Do not expose the    

 

 

charger to rain or snow.

 

• 

Do not use the charger if the cord is damaged or the charger is defective.

 

• 

Unplug the charger by pulling the adapter unit, not by pulling the cord.

 

• 

Do not cover the charger with anything.

 

• 

Do not use a step-up transformer or engine generator as the power  

 

 

 

source for the charger.

Содержание NAC-CN90

















Отзывы: