Dekolink Deko2119 Скачать руководство пользователя страница 51

Страница: 51 / 53

EKOLINK

IRELESS

. M

INI

-R

EPEATER

EKO

2119 P

RODUCT

ANUAL

Pub. 313-2006 Rev. 2.01S

Proprietary Data

Page 43

8.5.4.1 Temperature Warning

Most probable cause

: Unit temperature becomes high. .

Corrective action

: Check the Repeater case for external causes (sun, hot

environment, air flow is blocked). Eliminate the reason for excessive heat.

CAUTION

Do not cool with water

8.5.4.2 Temperature Shutdown

Most probable cause

: Unit temperature is too high. Mini-Repeater ceases

operation.

Corrective action

: Check the Repeater case for external causes (sun, hot

environment, air flow is blocked). Eliminate the reason for excessive heat.
Let the unit cool, forced air cooling is possible.

CAUTION

Do not cool with water

8.5.4.3 System Mute

Most probable cause

: Mini-Repeater amplification is muted

(automatically). .

Corrective action

: Check the LEDs in the Mini-Repeater. See paragraph

8.4.

8.5.4.4 User Mute

Most probable cause

: Mini-Repeater amplification is muted (manually). .

Corrective action

: This is the result of an operator action. Check RF

Transmission box in Link area in the Controls and Parameters pane. The
box should be empty. Click on it to change the LED status.

CAUTION

Check first the reason for the suppression of the function.

Check that the Mini-Repeater is not checked out in the

field.

Check the LEDs in the Mini-Repeater. See paragraph 8.4.

8.5.4.5 Panel Switch Mask

Most probable cause

: Mini-Repeater front panel LEDs are disabled.

Corrective action

: This is not a malfunction. Check the reason for the

action.

Содержание Deko2119





















































Результаты поиска

Содержание Deko2119

Отзывы:

Бренды по названию

Популярные бренды

Dekolink Deko2119, Руководство по эксплуатации продукта

Результаты поиска

Содержание Deko2119

Отзывы:

Бренды по названию

Популярные бренды