Dekolink Deko2119 Скачать руководство пользователя страница 50

Страница: 50 / 53

RODUCT

ANUAL

INI

-R

EPEATER

EKO

2119 D

EKOLINK

IRELESS

Page 42

Proprietary Data

Pub. 313-2006 Rev. 2.01S

8.5.3 Channeler Alarms and Troubleshooting

The Channeler alarms are provided for the Downlink and the Uplink paths.

The troubleshooting procedures for these alarms follow.

Figure 30: Mini-Repeater - Channeler Alarms

8.5.3.1 Lock Detect

This LED shows malfunction similarly for the Downlink and Uplink paths.

Most probable cause

: Downlink (Uplink) Channeler module lock-detect

failure.

Corrective action

: Check the LEDs in the Mini-Repeater. See

paragraph 8.4.

8.5.4 General Purpose Alarms and Troubleshooting

The general purpose alarms are provided for the Mini-Repeater as a unit, and
are not linked to the operation of the Downlink or Uplink paths.

The troubleshooting procedures for these alarms follow.

Figure 31: Mini-Repeater – General Purpose Alarms

Содержание Deko2119





















































Результаты поиска

Содержание Deko2119

Отзывы:

Бренды по названию

Популярные бренды

Dekolink Deko2119, Руководство по эксплуатации продукта

Результаты поиска

Содержание Deko2119

Отзывы:

Бренды по названию

Популярные бренды