DEK Brush Beast 36BB Скачать руководство пользователя страница 6

36BB, 36BDB 

 

 

 

Rev-4: 10/2010 

 

BRUSH BEAST  

Brush Mower 

BRUSH BEAST 

 

Operation Safety Precautions 

Equipment Operation—Safety Precautions 

1.  Do not operate the engine in a confined space 

where dangerous carbon monoxide fumes can 
collect. Carbon monoxide is odorless, 
tasteless, and can be fatal. 

2.  Mow only in daylight. 
3.  Make sure the mower is in neutral and the 

blades are disengaged before attempting to 
start the engine. 

4.  Be extremely careful when operating the 

mower on a slope or when the grass is damp 
or wet. Reduced traction could cause sliding. 

5.  Do not stop or start suddenly when going 

uphill. Use extreme caution when changing 
directions while operating on a slope. 

6.  Avoid steeps slopes. Never use riding 

attachments on slopes since there is an 
increased risk of roll over. 

7.  Never mow by pulling the mower back towards 

you because you might slip. 

8.  Watch for pedestrian or vehicular traffic when 

moving the mower while not in use (i.e., 
loading, unloading or transporting). 
 

9.  Never operate the mower with defective guards 

or shields, or without the safety devices 
securely mounted in place. 

10.  Never direct discharge of material toward 

bystanders nor allow anyone near the mower 
during operation. 

11.  Do not change the governor settings or over 

speed the engine. 

12.  Always stop the engine when you leave the 

mower, even for a moment. 

13.  To help reduce the fire hazard, keep the engine 

and the area around the engine free of grass, 
leaves or any other type of foreign material. 

14.  Beware of cutting edges. Always wear gloves 

for safety when performing blade maintenance 
activities. Beware on multiple blade units since 
the rotation of one blade may cause the rotation 
of the other blade. 

15.  Do not operate the mower with the grass chute 

deflector in the raised position. Serious injury 
could occur. 

IMPORTANT! The brush mower blades do NOT 

stop quickly. Visual indication that the blades 

are turning is provided at the center of the belt 

guard. DO NOT approach the brush mower 

deck for service, cleaning, removing debris, or 

for any other reason until after the visual 

warning disk has stopped completely. Even at 

slow speeds the blades can cause serious 

injury or death. 

GASOLINE IS HIGHLY FLAMMABLE AND 

EXPLOSIVE. FUEL LEAKS, A LOOSE FUEL TANK, 

OR A LOOSE FUEL VALVE CAN LEAD TO SEVERE 

INJURY OR DEATH. DO NOT OPERATE THIS 

BRUSH MOWER IF ANY COMPONENT OF THE 

FUEL SYSTEM IS LOOSE OR LEAKS GASOLINE! 

Before attempting to use your mower, make 
sure you are familiar with all of the 
components and have read the manual. 

Need Help? 

Parts, Service 

and Technical Assistance call: 

1-919-550-3221 

www.brushbeast.com

  

DANGER: Do not bypass, modify, alter or 
disconnect the safety system. Make sure that 
the safety interlock system is fully operational 
each time before mowing. 

Before setting up your brush mower, 
disconnect the spark plug wires from the 
spark plugs and ground them against the 
engine to prevent inadvertent starting. This 
step should be taken as a precaution 
whenever you are working on this machine. 

Содержание Brush Beast 36BB


























Отзывы: