background image

 

 

preliminary_fcc_lca-500_manual_en_896322_v200428_rev_3.docx 

 

Regulatory Notices 

Hereby, deister electronic declares that the radio equipment type LCA 500 is in compliance with Directive 

2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: 

http://go.deister.com/ce

 

 

 

 

Approved for use in all European countries.  

 

FCC 15.105 Statement: 

“This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications.  However, there is no guarantee that interference will not occur in a particular 

installation.  If this equipment does cause harmful interference to radio or television reception, which can 

be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures: 

–  Reorient or relocate the receiving antenna. 

–  Increase the separation between the equipment and receiver. 

–  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

–  Consult the dealer or an experienced radio/TV technician for help”. 

 

Changes or modifications not expressly approved by Deister could void the user’s authority to operation 

the equipment under FCC 15.21 requirements. 

 

Industry Canada Statement: 

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and 

Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two condi-

tions: 

1. This device may not cause interference. 

2. This device must accept any interference, including interference that may cause undesired operation of 

the device. 

 

The safe distance for nerve stimulation is 2 inches. 

 

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Inno-

vation, Sciences et Développement économique Canada applicables aux appareils radio exempts de li-

cence. L’exploitation est autorisée aux deux conditions suivantes : 

1. L’appareil ne doit pas produire de brouillage; 

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en  

compromettre le fonctionnement. 

La distance de sécurité pour la stimulation nerveuse est de 5 cm. 

 

Содержание LCA 500





















Отзывы: