Deif AGC-4 Mk II Скачать руководство пользователя страница 50

Страница: 50 / 50

Description

Notes

Add DG

Adds DG to the power management system.

Remove DG

Removes DG from the power management system.

Select yes on the display

Selects yes on the display in easy connect mode.

Select no on the display

Selects no on the display in easy connect mode.

Enable Easy connect

Enables Easy connect for the power management system.

Disable Easy connect

Disables Easy connect for the power management system.

5.19 Grid support

These commands are only available for genset and mains controllers.

Description

Notes

Activate Power Ramp [1-4]

Activate power ramp [1-4].

Var Reg Type Normal

Activate normal var regulation.

Var Reg Type Q/U U_SHIFT

See

Option A10

Var Reg Type Q/P REG CURVE

See

Option A10

Var Reg Type Q/U Q_SHIFT

See

Option A10

Var Reg Type FIXED COSPHI

See

Option A10

Var Reg Type FIXED Q

See

Option A10

Var Reg Type SUPERIOR

See

Option A10

(only in genset controllers).

Set Q(u) variant A ext. control to OFF

Set Q(u) variant A external control to OFF.

Set Q(u) variant A ext. control to MODBUS

Set Q(u) variant A external control to MODBUS.

Set Q(u) variant A ext. control to ANALOGUE Set Q(u) variant A external control to ANALOGUE.

Set Q(u) variant C ext. control to OFF

Set Q(u) variant C external control to OFF.

Set Q(u) variant C ext. control to MODBUS

Set Q(u) variant C external control to MODBUS.

Set Q(u) variant C ext. control to
ANALOGUE

Set Q(u) variant C external control to ANALOGUE.

Enable droop curve [1-2]

See

Option A10

Disable droop curve [1-2]

See

Option A10

Droop curve 2: Activate cosphi reference

See

Option A10

Droop curve 2: Activate Q reference

See

Option A10

Use Pset Min(Modbus/AI)

See

Option A10

5.20 Power limit inputs

These commands are only available for genset controllers.

Description

Notes

Power Limit Input (1-4)

Configure binary input 1 to 4 for RRCR (Radio Ripple Control Receiver) signals.

Application note 4189341276B EN

Page 50 of 50

Содержание AGC-4 Mk II



















































Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Похожие инструкции для AGC-4 Mk II

Бренды по названию

Популярные бренды

Deif AGC-4 Mk II, Руководство пользователя

Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Похожие инструкции для AGC-4 Mk II

Бренды по названию

Популярные бренды