manualshive.com logo in svg

DeDietrich GT 210 A, Руководство по эксплуатации

Поделиться
Скачать
DeDietrich GT 210 A Скачать руководство пользователя страница 7

7

01/08/08 - 82274096F

GT 210 A

L

X

8227N058A

3/4"-1"

To facilitate boiler transportation into the final installation site, a 

special handling tool (package BG 45, no.8218-7723) may be used 

as shown to transport the boiler or the boiler on the MLS horizontal 

domestic hot water tank. The two 3/4” or 1” pipes are shown are not 

supplied with the package BG45, they are supplied by others. 

Installation

1   Installing the boiler

The boiler does not require any special housekeeping pad as it has been provided with a study frame and leveling bolts for the 

final installation, but a non combustible pad is suggested to keep occasional water away from the boiler. The boiler requires 

clearance for combustibles and for servicing, the recommended clearance as shown in the table below. Do not install the boiler 

on combustible flooring or carpet. 
Proper combustion air and ventilation are required for the boiler, inadequate combustion air or makeup air provisions may result 

in foul boiler room odors, incomplete combustion resulting in carbon monoxide (CO) development or creation of negative building 

pressure. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Particular attention must be observed if the boiler is operating near or within vicinity of beauty shops, paint shops or 

industrial plant where known pollutants, corrosive element may containment affect the quality of combustion air supply, failure to 

observe this warnings will result in void of warranty of the boiler and any responsibility of De Dietrich. 
Consult local codes for combustion air and ventilation requirements, each installation must comply with all local and national 

codes having jurisdiction.  

Model

L = overall 

length

Sides

Rear

X = Front 

burner

Top

Vent

GT214A

29 

11/16  

[754mm]

GT215A

34 

11/16  

[881mm]

GT216A

39 

11/16  

[1008mm]

GT217A

32 

11/16  

[1135mm]

GT218

33 

11/16  

[1262mm]

20 inches 

[500mm]

20 inches 

[500mm]

34 inches 

[800mm]

24 inches 

[600mm]  in 

front of burner

Combustible & Service Clearances

GAS =        

6 inches 

[150mm]

OIL =         

9 inches 

[230mm]

Содержание GT 210 A























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды