manualshive.com logo in svg

Deckma Hamburg NLS 3000, Техническая документация инструкция, Страница: 23 / 27

Поделиться
Скачать
Deckma Hamburg NLS 3000 Скачать руководство пользователя страница 23

 

 

OPERATING MANUAL 

NLS 3000 NAVIGATION 

LIGHT CONTROL PANEL  

 

Tel: +49  (0)4105/65 60 – 0

   *   

DECKMA GmbH

   *   

Fax: +49  (0)4105/65 60 – 25 

E-mail: 

[email protected]

   

*

   Internet: 

www.deckma-gmbh.de

 

 

Page 23 of 27

 

 

 

5.0 Operation of the NLS 3000  

via graphic display BG-01E 

 

 

5.1  Switching on NLS 3000 and power supply switching 

 
Provided for switching the NLS 3000 on and off are control and indicating elements arranged on the 
bottom left of the screen. Two green LEDs (labelled "MAIN" and "EMGY") indicate via a steady light 
the  presence  of  the  respective  power  supply.  When  the  NLS  3000  is  switched  on,  the  LED  for  the 
currently used power supply lights up. 
 
Arranged  directly  next  to  the  "Power"  button  is  a  two-colour  LED. When  this  LED  lights  green,  both 
power supplies are present and the NLS is on. In the event of failure of one of the power supplies, this 
LED flashes red or shows a steady light. 
 
The NLS 3000 is switched on by pressing the "Power" button. The NLS 3000 can be switched off by 
pressing and holding the button for around 3 seconds. When the button is pressed during operation, 
switching takes place between the main and backup power supply. 
 
The  "SYS"  LED  lights  green  to  show,  that  the  NLS  3000  is  operating  without  faults  -  and  lights  red 
only on faults. 
 

5.2  Backlight brightness setting 

 
The display backlight has ten brightness settings. Provided for this purpose is the "Back Light" button. 
The brightness is increased one level each time this button is pressed. Selection takes place from the 
highest level to the lowest level. It is also possible to invert the display by pressing the "Invert Display" 
button. 
 
 

5.3  Alarm acceptance 

 
For the acceptance of alarms and simultaneously switching off the buzzer, the [SOUND OFF] button 
is provided. This is only displayed when the buzzer is active. 
 

5.4  Configurable functions 

 
In  order  to  simplify  the  setting  of  specific  light  scenarios,  these  buttons  can  be  defined  via 
configuration file (SD-memory card + data module DT01-E). Selection can subsequently be made via 
the buttons labelled according to their specific functions. 
 

5.5 Light buttons 

 

Each light is assigned to a button in the NLS 300 and can be switched on or off via this button. A two-
colour  LED  is  arranged  directly  on  the  right  next  to  the  button.  When  the  button  lights  green,  the 
associated light is on and the power is in the given range. The LED flashes red on faults in the light 
circuit. After acceptance of the fault, the LED shows a steady red light. 
 

Содержание NLS 3000




























Отзывы:

Нет отзывов