background image

Output Configuration

The Hot Stone Deluxe has 8 isolated outputs. All outputs are standard barrel type connectors 

wired “center negative”, which means the outside barrel is +V. This is the standard wiring for 
most guitar effect pedals. However, there are exceptions. Always check the label on the pedal 

before connecting, and use a polarity reversal cable if needed (see DC Cables section). 

Outputs 1 and 2

 are each configured with separate outlets for 9V and 12V. The 9 & 12V outlets

are both fed from the same transformer winding and can supply a combined maximum output 

current of 400mA. They can be used individually or simultaneously as long as the combined 
current draw does not exceed 400mA.

Outputs 3 and 4 

each provide up to 100mA of current at 9V. These outputs will run just about 

any battery operated 9V pedal.

Outputs 5 and 6

 each provide up to 200mA of current at either 9V or 12V. Use the switches 

SW1 and SW2 on the rear panel       to select the desired voltages.

Outputs 7 and 8

 each provide up to 100mA. The output voltage for each is variable using the 

control knob below the respective outlet  3 . Voltage is adjustable from 9V (fully clockwise) down
to about 5V (fully counter-clockwise). This can be used to simulate a used carbon battery, giving

transistor fuzz pedals a unique “brown” sound. The effect is not typically useful on effects which 
utilize opamps in the circuitry. The voltage control is not intended to be a calibrated control. The 

typical response when rotating the knob counter-clockwise will begin as a very gradual voltage 
drop, increasing near the end.

DC Cables

There are three types of DC cables included with the Hot Stone Deluxe:

1) 5.5x2.1mm (BLACK) to 5.5x2.1mm (BLACK): This is the standard cable used by most 

pedals (BOSS™, Ibanez™, DOD™, and most 9V pedals).

2) 5.5x2.1mm (BLACK) to 5.5x2.5mm center-positive (BLUE): This cable should be used 

with the Line6™ 4button modeling pedals and Eventide™ Factor pedals. These can also be
used for powering some AC powered effects (depending on current draw). 

3) 5.5x2.1mm (BLACK) to 3.5mm mini plug (tip positive): Use this to supply tip-positive 

voltage to any pedals using 3.5mm mini jacks.

Other types power cables can be purchased including:

Polarity reversal for pedals requiring 5.5x2.1mm “center-positive” connection.

Voltage Doubling cable for combining two outputs to create 18V or 24V

Current Doubling cable for combining two outputs to create double current.

Various lengths and end types are available for purchase.

1

2

3

4

5

6

7

8

4

SW2                SW1

Содержание Hot Stone Deluxe

Страница 1: ...es with 5 5x2 5mm blue barrel connector 1 DC cable with 3 5mm mini plug Manual and Warranty Declaration of Conformity Decibel Eleven declares that this product complies with the European Union Council Directives and Standards requirements for the Low Voltage Directive 2006 95 EC and the EMC Directive 2004 108 EC The European Union s EU WEEE Waste Electrical and Electronic Equipment directive is fo...

Страница 2: ... type fuse Should your Hot Stone Deluxe stop working where there is no power being supplied to your pedals and the green power indicator on the Hot Stone front panel is not lit it is recommended to check the condition of the fuse To access the fuse first be absolutely certain that the unit is detached from its AC power cable Then remove the 2 flat head screws along the bases of the front and rear ...

Страница 3: ...se down to about 5V fully counter clockwise This can be used to simulate a used carbon battery giving transistor fuzz pedals a unique brown sound The effect is not typically useful on effects which utilize opamps in the circuitry The voltage control is not intended to be a calibrated control The typical response when rotating the knob counter clockwise will begin as a very gradual voltage drop inc...

Страница 4: ...r 2 at 12V using the BLUE 5 5x2 5mm cable It is also possible to power them using a current doubling cable from outputs 5 and 6 set to 12V Strymon pedals can be powered from output 1 or 2 at 9V using the standard BLACK cable Other pedals will list power requirements in their manual or on the pedal itself Some manufacturers list actual power requirements while others may list only the rating of the...

Отзывы: