decaWave DW1000 Скачать руководство пользователя страница 169

Страница: 169 / 242

DW1000 User Manual

Version 2.12

Page 169 of 242

Table 46: Configurations maintained in the AON Memory Array

Configuration Register

Register file: 0x03 – PAN Identifier and Short Address

Sub-Register 0x28:0B– RF_RXCTRLH

Register file: 0x04 – System Configuration

Sub-Register 0x28:0C– RF_TXCTRL

Register file: 0x08 – Transmit Frame Control

Sub-Register 2A:0B – TC_PGDELAY

Register file: 0x0E – System Event Mask Register

Sub-Register 0x2B:07 – FS_PLLCFG

Register file: 0x1D – SNIFF Mode

Sub-Register 0x2B:0E – FS_XTALT

Register file: 0x1E – Transmit Power Control

Sub-Register 0x2C:00 – AON_WCFG

Register file: 0x1F – Channel Control

Sub-Register 0x2C:06 – AON_CFG0

Register file: 0x21 – User defined SFD sequence

Sub-Register 0x2C:0A – AON_CFG1

Sub-Register 0x23:04 – AGC_TUNE1

Sub-Register 0x2E:1804 – LDE_RXANTD

Sub-Register 0x23:04 – AGC_TUNE1

Sub-Register 0x2E:1806– LDE_CFG2

Sub-Register 0x23:12 – AGC_TUNE3

Sub-Register 0x2E:2804 – LDE_REPC

Sub-Register 0x26:00 – GPIO_MODE

Sub-Register 0x36:00 – PMSC_CTRL0

Register file: 0x27 – Digital receiver configuration

Sub-Register 0x36:04 – PMSC_CTRL1

Sub-Register 0x36:0C – PMSC_SNOZT

Sub-Register 0x36:28 – PMSC_LEDC

Only the

Low 32-bits are maintained.

All bits

are maintained except for bit 0. Bit zero it is lost and restored as 0.

Only the

SFD_LENGTH

field in the first octet is maintained.

The TX antenna delay in

Register file: 0x18 – Transmitter Antenna Delay

is not preserved, but instead ends up corrupted by part

of the preserved RX antenna delay. After a wake-up then for correct TX time stamping The TX antenna delay will need
reprogramming.

Bits preserved are: 23, 15, 12, 11 and 6. The remainder revert to their reset value during wake-up init.

All preserved except for the

KHZCLKDIV

field which revert to its reset value during wake-up init.

Just the

BLNKEN

bit is preserved, the

BLINK_TIM

field reverts to its reset value during wake-up init.

Содержание DW1000



















































































































































































































































Результаты поиска

Содержание DW1000

Отзывы:

Похожие инструкции для DW1000

Бренды по названию

Популярные бренды

decaWave DW1000, Руководство пользователя

Результаты поиска

Содержание DW1000

Отзывы:

Похожие инструкции для DW1000

Бренды по названию

Популярные бренды