manualshive.com logo in svg

Decatur Electronics SVR DUAL, Руководство пользователя

Поделиться
Скачать
Decatur Electronics SVR DUAL Скачать руководство пользователя страница 22

SVR DU

AL

™

  

U

ser
’s M
anual

22

The sixth is [SNR,SS .SSS,SNRR,RRR .RRR<cr>] where:

1 .  SNR is the signal to noise ratio for the velocity .

2 .  SS .SSS is the velocity of the water .

3 .  SNRR is the signal to noise ratio for the level sensor .

4 .  RRR .RRR is the distance measurement to the water surface .

The seventh is [DSS .SSS,RRR .RRR<cr>] where:

1 .  D is the direction of the water flow and can be "+" or "-" or 

"?" if unknown .

2 .  SS .SSS is the velocity of the water

3 .  RRR .RRR is the distance measurement to the water surface .

The 2nd & 3rd options are "VELOCITY SPECTRUM" and "DEBUG"

The second option is   ."Velocity Spectrum" and is designed for 
engineering use to calculate the FFT (Fast Fourier Transform) .

The third option is "Debug" and is designed for engineering use 
and prints out a list of variables .

•  Note: User must send the exact serial number that 

matches what is currently programmed into the radar 
unit for it to transmit data, otherwise the request will 
be ignored . User has the ability to program the serial 
number as needed . (In this case the serial number 
becomes the MODBUS address of the radar .)

Once new protocols or options have been selected, press the OK 
button . The Configure program will save the new settings into 
memory and the SVR Dual™ will start each time with these new 
settings until you change them again .

4.5  Loading New Firmware & Configuring the SVR D

u

al™

From time to time Decatur Electronics will release new firmware 
for the SVR Dual™  . If you have received new firmware then save 
the firmware to a file on your hard drive remembering the path to 

Содержание SVR DUAL














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды