manualshive.com logo in svg

DEC VR297, Руководство пользователя, Страница: 23 / 36

Поделиться
Скачать
DEC VR297 Скачать руководство пользователя страница 23

Adjustments

15

2.1 Before You Start

Let the monitor warm up for at least 20 minutes before performing any

adjustments on the monitor. The warm-up time ensures that the electron

guns are at a stable temperature before you do any adjustments.

NOTE

If a customer calls with a display-quality problem, ask the

customer to leave the monitor on until you arrive. Then you

only need to let the monitor warm up for 5 minutes after you

remove the rear cabinet assembly.

Before you perform adjustments, set up the monitor as follows. First

remove the rear cabinet assembly (Section 3.1).
1. Place the monitor on a nonconductive surface.
2. Reconnect the video cables.
3. Reconnect the power cord.
4. Press the power switch on ( | ). Wait for a video display to appear on

the screen.

Displaying Screen Test Patterns

For some procedures in this chapter, you must display a circle-crosshatch

or screen of E’s diagnostic pattern (Appendix B). To display these patterns,

refer to your host system’s service manual and follow the procedures for

accessing diagnostic screen patterns.

Содержание VR297





































Отзывы:

Нет отзывов