Dea REV Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 26

Dea REV Series Скачать руководство пользователя страница 7

24

5.2 ELECTRICAL CONNECTIONS FOR 230V MODELS

Execute the wiring following the directions of “Table 2” and diagrams on page 25.

WARNING

To ensure an appropriate level of electrical safety always keep the 230V power supply cables apart (minimum 4mm

in the open or 1 mm through insulation) from low voltage cables (motors power supply, controls, electric locks, aerial and auxiliary
circuits power supply), and fasten the latter with appropriate clamps near the terminal boards.

WARNING

Connect to the power supply 230 V ~± 10% 50 Hz through a multi pole switch or a different device that can ensure

multi pole disconnection from the power supply, with a contact opening of 3 mm.

WARNING

To connect the encoder to the control panel, use only a dedicated cable 3x0,22mm

2

.

Tabella 2 “collegamento alle morsettiere”

1-2

230 V ~ ±10% (50/60 Hz) power supply input

3-4-5

Operator 1 output 230 V ~ max 600W

6-7-8

Operator 2 output 230 V ~ max 600W (if present)

9-10

230 V ~ max 150 W output for open gate warning light (if P052=0) or courtesy light (if P052>1)

11-12

Flashing light output 230 V ~ max 40W

13-14

13 (-)

“Boost” output for electric-lock, max 1 x art. 110 (if P062=0), 24V pulse output, max 5W (if P062=1),
step by step (if P062=2), electro-brake output for not self-locking operators (if P062=3), output for
electric-lock power supply via external relay (if P062=4), output for electro-magnets power supply for
barriers (ifP062=5) or temporized output (if P062>5).

14 (+)

15-16

Output 24V

max 100mA; by selecting the FL/WL jumper, you can choose the 230 Flash output as a

24V output (if the jumper is set to FL) or as a Warning light output (if jumper set to WL).

Warning:

the output capacity allows to use LED flashing lights only

17-18

17 - N.C.

Input 6 FCC 1. If it intervenes it stops M1 closing.

If unused, short circuit

.

If

the

installation

requires

different

comman

-

ds

and

/

or

add

itional

to

the

standard,

you

can

configure

each

input

to

the

required

rate.

R

efer to Chapter

“

Advanced Programming”.

18 - Com

19-20

19 - N.C.

Input 5 FCA 1. If it intervenes it stops M1 opening.

If unused, short circuit

.

20 - Com

21-22

21 - N.C.

Input 4 PHOTO 1. When enabled (see parameter P050 in the table), activation of

PHOTO 1 provokes: an inversion of direction (during closing), the arrest of the mo-

vement (during opening), prevent the start (gate closed).

If unused, short circuit

.

22 - Com

23-24

23 - N.C.

Input 3 SAFETY. If activated, it causes the inversion. See P055 and P056 on the para-

meters table.

If unused, short circuit

.

24 - Com

25-26

25 - N.O.

Input 2 PED. If activated, it opens motor nr. 1 only.

26 - Com

27-28

27 - N.O.

Input 1 START. In case of intervention it provokes: the operator opening or closing. It

may operate as “inversion” mode (P049=0) or “step by step” mode (P049=1).

28 - Com

29

Aerial signal input

30

Ground aerial input

31-32

24 V ~ power supply output for auxiliary devices 200mA

33-34

33 (+)

DE@NET mains input (unused at the moment)

34 (-)

«
...
5
6
7
8
9
...
»

Содержание REV Series



























Отзывы:

Нет отзывов