De Vielle DEF963739, Инструкция по эксплуатации

Страница: 9 / 12

9
Press the Fahrenheit/Celsius button to
display the preferred temperature scale.
The Timer button allows a time to be set
between 1 to 24 hours. Press the Timer button
until the desired time is shown on the display
(e.g. 01h 00m). Each press of the Timer button
will increase the length of time in 1 hour
increments. The heater will countdown and once
the selected time has elapsed the heater will
switch off automatically.
To turn the heater off, press the On/Off button on
the Control Panel again. Then turn the Power
Switch at the side of the heater to “O” position.
Operating your Appliance
REMOTE CONTROL
The remote control buttons perform the same
functions as those on the Control Panel of the
unit.
For best results, aim the remote directly at the
display screen on the front of the heater. The
remote has a 3 metre range of operation.
The remote control requires one "CR2032" type
battery. Remove the plastic tab from the battery
and battery terminal prior to first use of the
remote control.
SAFETY DEVICES
This appliance has three protection devices:
1. Tilt switch - this will automatically turn the
appliance off if the appliance is not in the
appropriate operating position.
2. Resettable thermal link - this will
automatically disconnect the power to the
appliance at a pre-set overheat temperature.
After cooling down it will reset and power on
again. If this occurs, investigate what is
causing the appliance to overheat.
3. Thermal fuse - this disconnects the
appliance permanently in case of
overheating. (It is non resettable).
CAUTION: The appliance generates heat during
use. Proper precautions must be taken to
prevent the risk of burns, scalds, fires or other
damage to persons.
CARE AND CLEANING
The appliance requires regular cleaning to
ensure trouble free operation:
Unplug the appliance from the mains supply
before cleaning.
Ensure that the appliance has been allowed to
cool down completely before cleaning.
Use a damp cloth (not wet) to wipe the exterior of
the appliance to remove dust and dirt.
Never use solutions such as benzene, thinners or
polishing agents.
Use a vacuum cleaner to remove dust and fluff
from around the grills.
Ensure the appliance is dry before plugging back
into the mains supply.
Do not attempt to dismantle the Heater.
There are no user serviceable parts. For service
or repair, contact an authorised electrical service
technician.
SUPPORT AND TECHNICAL ADVICE
Goldair
–
New Zealand
Monday – Friday 8am-5pm
Phone +64 (0)9 917 4000
Phone 0800 232 633
info@cdb.co.nz
Goldair
–
Australia
Monday – Friday 8am-5pm
Phone +61 (0)3 9365 5100
Phone 1300 465 324
info@cdbgoldair.com.au
TECHNICAL SPECIFICATION
Model No: GCV340
Supply: 220-240VAC 50Hz
Wattage: 2300W
Technical details
Product Model NO.
DEF963739/CH-09FLCD
Voltage 220-240V~
Frequency 50Hz
Power 2300W
SAFETY FEATURE
The heater is fitted with a resetting thermal cut-
out. In normal use the thermal cut out will not
take any action.
If the unit overheats, it will cut out automatically.
If this happens, unplug the device and check
for any blockages or covering of air vents and
remove. After approximately 10 minutes, the unit
will cool down and operate normally.
Press the Fahrenheit/Celsius button to
display the preferred temperature scale.
The Timer button allows a time to be set
between 1 to 24 hours. Press the Timer button
until the desired time is shown on the display
(e.g. 01h 00m). Each press of the Timer button
will increase the length of time in 1 hour
increments. The heater will countdown and once
the selected time has elapsed the heater will
switch off automatically.
To turn the heater off, press the On/Off button on
the Control Panel again. Then turn the Power
Switch at the side of the heater to “O” position.
Operating your Appliance
REMOTE CONTROL
The remote control buttons perform the same
functions as those on the Control Panel of the
unit.
For best results, aim the remote directly at the
display screen on the front of the heater. The
remote has a 3 metre range of operation.
The remote control requires one "CR2032" type
battery. Remove the plastic tab from the battery
and battery terminal prior to first use of the
remote control.
SAFETY DEVICES
This appliance has three protection devices:
1. Tilt switch - this will automatically turn the
appliance off if the appliance is not in the
appropriate operating position.
2. Resettable thermal link - this will
automatically disconnect the power to the
appliance at a pre-set overheat temperature.
After cooling down it will reset and power on
again. If this occurs, investigate what is
causing the appliance to overheat.
3. Thermal fuse - this disconnects the
appliance permanently in case of
overheating. (It is non resettable).
CAUTION: The appliance generates heat during
use. Proper precautions must be taken to
prevent the risk of burns, scalds, fires or other
damage to persons.
CARE AND CLEANING
The appliance requires regular cleaning to
ensure trouble free operation:
Unplug the appliance from the mains supply
before cleaning.
Ensure that the appliance has been allowed to
cool down completely before cleaning.
Use a damp cloth (not wet) to wipe the exterior of
the appliance to remove dust and dirt.
Never use solutions such as benzene, thinners or
polishing agents.
Use a vacuum cleaner to remove dust and fluff
from around the grills.
Ensure the appliance is dry before plugging back
into the mains supply.
Do not attempt to dismantle the Heater.
There are no user serviceable parts. For service
or repair, contact an authorised electrical service
technician.
SUPPORT AND TECHNICAL ADVICE
Goldair – New Zealand
Monday – Friday 8am-5pm
Phone +64 (0)9 917 4000
Phone 0800 232 633
info@cdb.co.nz
Goldair – Australia
Monday – Friday 8am-5pm
Phone +61 (0)3 9365 5100
Phone 1300 465 324
info@cdbgoldair.com.au
TECHNICAL SPECIFICATION
Model No: GCV340
Supply: 220-240VAC 50Hz
Wattage: 2300W
For your convenience, there is a holder
on the side of the heater for storing the
remote control.