OPERATION
REMOVE ALL DEBRIS FROM THE GLASSES TO BE WASHED BEFORE PLACING THEM INTO THE BASKET.
CLOSE THE DOOR - PRESS THE
CYCLE START SWITCH
- THE CYCLE LAMP WILL COME ON.
AT THE END OF THE
CYCLE THE
WASH CYCLE LAMP
WILL GO OUT - OPEN THE DOOR AND PULL OUT THE BASKET.
ALLOW EXCESS WATER TO RUN OFF BEFORE REMOVING.
ROUTINE MAINTENANCE
AT THE END OF A SESSION TURN OFF THE
POWER SWITCH.
DO NOT REMOVE THE
FILTER
AT THIS STAGE.
REMOVE THE
DRAIN PLUG
- THE WASH TANK WILL EMPTY - (MACHINES FITTED WITH DRAIN PUMP WILL AUTOMATICALLY START TO PUMP THE WATER OUT).
COLLECT THE DEBRIS AND REMOVE FROM THE WASH TANK.
CLEAN AROUND THE WASH TANK - DOOR SURROUNDS AND HINGES WITH AN 'ADDIS'’ TYPE WASHING UP BRUSH AND CLEANING CLOTH.
DO NOT USE CHLORIDE OR BLEACH CONTAINING BASED CLEANING SOLUTIONS OR ABRASIVES WHEN CLEANING THE WASH TANK.
TAKE OUT THE
MAIN FILTER
- CLEAN THOROUGHLY AND REPLACE .
DO NOT ALLOW DEBRIS TO GO DOWN THROUGH THE
FIXED FILTER
AND
OUTLET HOLE
AS THIS MAY DAMAGE YOUR MACHINE.
REGULARLY CHECK
RINSE JETS
AND
WASH JETS
ARE CLEAR OF DEBRIS OR LIME SCALE - REMOVE IF NECESSARY BY UNSCREWING THE
RINSE ARM NUT
THAT HOLDS THE
RINSE ARM
IN PLACE - REMOVE THE
RINSE PIN
THAT HOLDS THE
WASH ARM
IN PLACE - CLEAN BOTH THOROUGHLY AND REASSEMBLE.
SERVICE CALLS TO RECTIFY FAULTS CAUSED BY `THE LACK OF ROUTINE MAINTENANCE` WILL BE CHARGED FOR
AND YOUR WARRANTY MAY BE AFFECTED
www.directcatering.co.uk
(OPTIONAL DRAIN PUMP)
REMOVE DRAIN PLUG THEN
SWITCH THE MACHINE OFF
TO START THE AUTOMATIC
DRAIN PUMP CYCLE
MAIN FILTER
OUTLET HOLE
FOOT VALVES FOR
CHEMICAL
CONTAINER TUBES
RINSE ARM NUT
RINSE
JETS
WASH JETS
RINSE PIN
RINSE ARM
WASH ARM
FIXED FILTER
DRAIN PLUG
SALT CONTAINER
LID
WATER SOFTENER REGENERATION
THE
SALT LOW LAMP
WHEN ON WARNS IF THE SALT CONTAINER IS EMPTY.
UNSCREW THE
SALT CONTAINER LID
LOCATED INSIDE THE WASH TANK AND FILL WITH GRANULAR CATERING SALT ( THE FULL CONTAINER WILL
APPROXIMATELY REGENERATE FOUR REGENERATION CYCLES & HOLDS 1 Kg OF SALT).ENSURE THE
SALT CONTAINER LID
IS SECURE AFTER FILLING.
REMOVE THE
DRAIN PLUG
FROM THE MACHINE DURING THE REGENERATION OF THE WATER SOFTENER.
THE MACHINE
POWER SWITCH
MUST BE OFF TO ENABLE THE REGENERATION CYCLE.
CLOSE THE DOOR AND PRESS THE
REGENERATION SWITCH
. THE
WATER SOFTENER REGENERATION LAMP
WILL COME ON.
THE REGENERATION OF THE WATER SOFTENER WILL TAKE AROUND 20 MINUETS AND WILL BE FULLY AUTOMATIC.
THE
WATER SOFTENER REGENERATION LAMP
WILL GO OUT AND THE MACHINE WILL SWITCH OFF AUTOMATICALLY AFTER THE REGENERATION
CYCLE IS COMPLETE. REMEMBER TO REPLACE THE
DRAIN PLUG
BEFORE RE-FILLING THE MACHINE.
MEDIUM-WATER HARDNESS MAY REQUIRE FOUR REGENERATIONS A WEEK. MEDIUM TO HARD-WATER HARDNESS MAY REQUIRE DAILY REGENERATION.
POWER
SWITCH
CYCLE START
SWITCH
WATER SOFTENER
START SWITCH
(REMOVE DRAIN PLUG DURING THE REGENERATION)
POWER
LAMP
WASH CYCLE
LAMP
REGENERATION
LAMP
SALT LOW
LAMP
MACHINE READY
LAMP
PREPARATION
CHECK THE
DRAIN PLUG
IS
PUSHED
FIRMLY IN PLACE AND
FILTERS
ARE PROPERLY SECURED.
CHECK THE
DETERGENT
CHEMICAL ( RED ) AND
RINSE AID
CHEMICAL ( CLEAR ) SUPPLY TUBES - WITH
FOOT VALVES
- ARE SUBMERGED IN SUFFICIENT PRODUCT.
CHECK THE DOOR IS CLOSED AND PRESS THE
POWER
SWITCH
- THE GREEN
POWER LAMP
WILL COME ON.
ALLOW 30 MINUTES FOR THE MACHINE TO FILL WITH WATER AND REACH THE CORRECT WASHING TEMPERATURE.THE
MACHINE READY LAMP
WILL COME ON.
OPERATING AND MAINTENANCE INSTRUCTIONS
SG35 IS D / SG40 IS D / SG45 IS D / SG50 IS D
