background image

complying  with  AS1337  Eye  protectors  for  industrial  applications 

should be provided and used;

•  Protection from sun, workers should be protected from sunlight/UV 

radiation  by  using  a  sunscreen  with  a  sun  protection  factor  (SPF) 

rating of at least 30+ and by wearing hats, shirts with long sleeves 

and long trousers. 

4.0  USING  THE  ANCHOR  ON  THE  GO™  WITH  FALL 

ARREST EQUIPMENT.

The  anchor  should  be  fitted  in  accordance  with  the  manufacturer’s 

instructions (Section 2.0) at the edge of the non working side of the roof.

Step 1: The operator should inspect and don a fall arrest rated harness 

fitted with a frontal fall arrest point and adjust it to ensure it is correctly 

fitted and comfortable. Capital Safety always recommends that a shock 

absorber  be  used  between  the  rope  grab  and  the  connection  point  to 

reduce the risk of injury in a fall. The rear (dorsal) fall arrest connection 

point  is  also  deemed  an  appropriate  connection  point  however  its 

selection/use will depend on the type of work being completed.

Step 2: Once the Anchor on the Go™ is installed as per instructions in 

Section 2.0, ensure the rope is of sufficient length to hang two metres 

past the proposed connection point on the alternative side of the roof 

in order to facilitate attachment to a fall arrest attachment point prior 

to  leaving  the  ladder  or  scaffold.  The  rope  should  be  pulled  tight  and 

tensioned to ensure all slack has been taken up before connection. If the 

rope grab is already on the rope, ensure it is positioned at the free end.

Step 3: The roof should then be accessed from the working side, the 

operator  connecting  the  rope  grab  to  the  rope  (or  accessing  the  rope 

grab permanently attached to the rope) and the shock absorber to the 

rope grab before moving from the ladder or scaffold onto the roof. 

Step 4: To minimise the fall distance resulting from any slip or fall, it is 

important to have the least amount of slack on the line at any point in 

time. This means regular and small adjustments of the rope grab up and 

down the rope in line with the required movement on the roof. Refer to  

Figure Six over the page.

When moving up the roof, the manual rope grab should be opened and 

11

Содержание Anchor on the Go





















Отзывы: